manualshive.com logo in svg

LORD 6254-4220, User Manual

Share
Download
LORD 6254-4220 User Manual Download Page 16

3DM

®

-GX5-15

User Manual

NOTE

When selecting sensor and estimation outputs to be recorded, communications bandwidth

considerations should be taken into account. Lower baud rates equate to lower

communications bandwidth, which can be consumed quickly by selecting a large number of

measurements at high sample rates. Overrunning the communications bandwidth will result

in dropped communications packets and lost data.

3.5.1

Saving Configurations

Sensor settings are saved temporarily by selecting the OK button in the Device Setup window after

configuration, but they are lost when the device is powered off. To save current settings, so they are

automatically restored the next time the device is powered on, select Settings > Save Current

Settings.

First adjust the sensor settings to the desired values. Next select Settings > Save Current Settings

from the main window (

Figure 10 - Save Sensor Settings

). The settings will now remain intact when

the sensor is powered off and then on again.

To recall the last saved settings select Settings > Load Startup Settings. To revert the settings back

to the factory defaults, select Settings > Load Default Settings.

Figure 10 -Save Sensor Settings

16

Summary of Contents for 6254-4220


































































Reviews:

No comments

Brands by name

Popular brands

Load more brands