TM 11-5820-919-40-2
ANTENNA TUNER A2A2 ALIGNMENT
The alignment procedure is to be used in either of these situations: (1) the performance test calls a potentiometer out of adjustment, or (2) one of the following is
replaced:
1.
Comparator/Control Hybrid A1
2.
RF Sensor Bridge
The procedure consists of a preliminary setup and adjustment procedure. The adjustment procedure can be shortened by adjusting R1, R2, B3 and R4 to the values
given in step 13 below. The complete procedure need only be run if work has been done on the rf Sensor Bridge.
PRELIMINARY SETUP
1. Connect test radio as in figure 10-5.
2. Connect an rf signal generator to the input of the
power amplifier module at A1J1. Set the level to
-100dbm and the frequency to 2.000 MHz.
3. Remove the antenna tuner module from the test
bed radio. Separate the two halves of the antenna
tuner module which is to be aligned, except for the
interconnecting ribbon cable.
4. Plug the antenna tuner module to be aligned into
the test bed radio.
5. Connect the 100 ohm load (figure 3-11E, TM 11-
5820-919-40-1 to the radio set BNC connector.
6. Set the radio control to the following:
a.
FREQUENCY KHz to 02,000.0
b.
MODE to V-TR
c.
SB to USB
d.
VOLUME to on
e.
ANT SEL to BNC
ADJUSTMENT
1. Close CW KEY and switch MODE to V-RCV and
back to V-TR. This generates a tune start pulse.
2. Ground (continuously) E7 of ribbon cable.
3. Increase level of rf signal generator until TP13 is
+10v rms. This corresponds to 2 watts in a 50-ohm
system.
4. Measure the dc output of the Z sensor at TP12.
Record voltage at TP12.
5. Adjust R4 until the Z comparator reference
voltage, TP10, is the same as that measured in step
4.
6. Replace the 100 load with the 130-ohm load (figure
3-11-F, TM 11-5820-919-40-1).
7. Adjust the rf signal generator so that the voltage at
TP13 varies b7 ant +14v (+7v = 1 watt, +14v
= 4 watts) and measure the output of the vswr
detector at TP11. But, do not stay at the 4-watt level
for any length of tine.
8. Adjust the level compensation resistor, R7, for
minimum variation in do output of TP11 as performed
in step 7.
9. Once R7 is adjusted, adjust the rf signal generator
so that TP13 is +10v rms, Note the voltage at TP11.
ADJUSTMENT (cont)
10. Adjust B3 until the 1.5 vswr reference voltage,
TP9, is the same as that noted in step 9.
11. Adjust B2 until the 1.6 vswr reference voltage at
TP8 is +10.6v higher than that of TP9.
12. Adjust B1 until the voltage at TP7 is +3.0v.
13. The following are typical settings after alignment:
ALC REM
R1
TP7
+3.0v
1.6 REP
R2
TP8
+4.3v
1.5 REP
R3
TP9
+3.7v
ZREF
R4
TP10
+3.3v
14. Turn radio off and disconnect test equipment.
Reassemble the two boards of the antenna tuner
module being very careful to avoid pinching the ribbon
cable.
96
Summary of Contents for AN / PRC- 1 04(A)
