background image

www.loosnaples.com

Toll Free: 800-321-LOOS (5667)

14

WARRANTY (CONT.)

Huskie  reserves  the  right  to  determine  all  warranty  claims.  Huskie  will 
not waranty tools containing parts or batteries not originally supplied by 
Huskie. Failure due to misuse, improper maintenance, misapplication, not 
following instructions or warnings, abuse or repairs attempted by anyone 
other than Huskie Tools, Inc. or an authorized service center renders this 
warranty null and void.

Repair and Warranty Claims

All  claims  must  be  sent  to  Huskie  for  inspection  and  authorization.  A         
Return  Goods Authorization  (RGA)  is  required  before  shipping  tools  to 
Huskie.  Secure  the  authorization  by  telephoning  or  writing  to  Huskie’s 
main  office  with  details  of  the  claim.  Non-warranty  repairs  are  handled 
using the same procedure. Repairs exceeding 50 percent of the cost of a 
new tool will be advised before repairs are made.

Payment Terms

Upon credit approval, Huskie’s standard payment terms are net-30 days. 
Visa, Mastercard, Discover, and American Express are also accepted.

Freight

All Huskie Tools are FOB, Glendale Heights, Illinois. Goods will be shipped 
pre-paid and added, unless otherwise specified. Freight shipments over 
$17,000 are pre-paid.

Quotations

Special quantity quotations should be phoned in to discuss the scope of 
your tool requests.

Summary of Contents for Cableware Locoloc HC-S724H





















Reviews: