background image

MAINTENANCE 

- 15 - 

  Improper maintenance, or failure to correct a problem before 
operation, can cause a malfunction by which you can be hurt or 

killed. 
Always follow the inspection and maintenance recommendations and schedules 
in this owner

s manual.

 

 

1) Engine oil change 

Drain the engine oil when the engine has been warmed to ensure complete and rapid 
draining. 

1

.

 

Remove the oil dipstick and screw off the drain plug to drain the engine oil 

2

. Reinstall the oil drain plug and tighten it. 

3

. Refill with the recommended engine oil 

and check oil level.

 

 

Engine oil volume: 
168F-II: 0.6L 
188F: 1.1L 
 

  Engine oil may cause skin cancer if repeatedly left in contact 

with the skin for prolonged periods. Although the skin cancer does not 

necessarily happen, it is still advisable to thoroughly wash the skin that has 

contacted engine oil with soap and water after handling engine oil. 

 

For the sake of environment protection, please treat the used engine oil in an 
appropriate way. We strongly advise you to store the used engine oil in a sealed 
container and take it to the local service station or recycling center for used oil 
reclamation. Never throw it in the trash or pour it on the ground or into the ditch. 
 

2) Air filter maintenance 

A dirty air filter will restrict air flow into the carburetor. To prevent carburetor 
malfunction, maintain the air filter regularly. Maintain it more frequently when operating 
the generator in extremely dusty areas. 
 

Using gasoline or inflammable solvent to clean the filter element 

can cause a fire or explosion. Use only soapy water or nonflammable solvent. 

 

Never run the generator without the air filter, or rapid engine wear 

will result. 

 

Drain plug 

Oil dipstick 

Highest oil 

level 

Summary of Contents for LC2500-J




























Reviews: