Logic DLC NET Series Use And Maintenance Manual Download Page 26

Page: 26 / 78

USE AND MAINTENANCE MANUAL

– DLC

NET

Series

Installation

LOGIC S.r.l. - M0145Db.docx

Mod. L0006A01 of 30/05/2016

Page 26 of 78

Below are listed the serial configuration parameters for communication with
DLC

NET

. These parameters are already set on both instruments, with no need for

any settings:

Table 7. Serial port parameters for communication with Logic DLC3-RD

Parameter

Value

Transmission

Asynchronous

Baud rate

19200

Word

8 bits

Stop bit

Parity

None

3.6.3

RS-485 connection
with display BEKA

BA488C

The connection with the remote display BEKA

BA488C in hazardous area must

be through the BEKA

BA201 barrier, as shown in Table 8 and in Figure 17. The

settings of the remote display to be set for correct operation are shown in Figure
17.

The shield must be connected at one point only, cabinet side (DLC

NET

), for

better immunity to low frequency noise (

ground loop

Table 8. Connection with remote display for safe area BEKA

BA488C

Terminal

Connection

TB3-1

GND / Shield

TB3-2

TB3-3

Figure 17. Connection of DLC

NET

to display BEKA

BA488C

Summary of Contents for DLC NET Series















































































Search results

Summary of Contents for DLC NET Series

Reviews:

Logic DLC NET Series, Use And Maintenance Manual, Page: 26 / 78

Search results

Summary of Contents for DLC NET Series

Reviews: