background image

3

Hydraulic Flail Mower OM

Owner Information

Thank you for your decision to purchase a Hydraulic Flail 
Mower from Loftness. To ensure maximum performance 
of your machine, it is mandatory that you thoroughly study 
the owner’s manual and follow its recommendations. 
Proper operation and maintenance are essential to 
prevent injury or damage and to maximize machine life.

The Loftness Hydraulic Flail Mower is an effective, 
reliable machine used for maintaining grass and 
controlling weeds. Operate and maintain this machine 
in a safe manner and in accordance with all applicable 
local, state, and federal codes, regulations and/or laws, 
and in compliance with on-product labeling and these 
instructions.

Make sure that all personnel have read this owner’s 
manual and thoroughly understand safe and correct 
operating, installation and maintenance procedures.

Continuous improvement and advancement of Loftness 
products may result in changes to your equipment 
that may not be reflected in this publication. Loftness 
reserves the right to make product improvements to the 
machine at any time. Although great care has been taken 
to ensure the accuracy of this publication, Loftness does 
not assume any liability for errors or omissions.

Warranty Policy

Be sure to read and understand the Warranty Policy at 
the beginning of this manual. It is also important that you 
fill out the Warranty Registration form(s) completely with 
your dealer so as not to void the warranty.

Serial Number Location

1

2

The arrows above indicate the location of the serial 
number tag (1) and the location of the serial number 
stamped into the frame (2).

Always use your model and serial number when 
requesting information or when ordering parts.

Manual Storage

Keep the owner’s manual and the entire documentation 
packet in the storage compartment provided on your 
flail mower. The owner’s manual must be available for all 
operators.

Introduction

Summary of Contents for 60MH



















































Reviews: