background image

LOFA EP250 Operation and Troubleshooting

2

463-3000-01 Rev C.1 - 28-Feb-2007

Warning

When replacement parts are required, LOFA Industries recommends using replacement parts

supplied by LOFA or parts with equivalent specifications.

Failure to heed this warning can lead to premature failure,

product damage, personal injury or death.

Important Safety Information

The warnings in this publication are not all inclusive.

LOFA Industries cannot anticipate every potential hazard.

Appropriate safety rules and precautions should be followed with any

tool, work method or operating procedure.

Improper procedures, tools and materials may cause

damage or make the equipment unsafe to operate.

Only persons with appropriate training, skills and tools

should perform these functions.

Improper operation, maintenance or repair of this product can be

dangerous and may result in injury or death.

Do not operate or perform any maintenance or repair on this product until all operation,

maintenance and repair information is read and understood.

The information, specifications, and illustrations in this publication are based on information

available at the time of publication.

All items are subject to change at any time without notice.

Summary of Contents for EP250




















Reviews: