background image

 

Press the Next ► arrow key on the SMART SYSTEM display to access Screen 5. 

5

 

WHR CFH: OFF

 

The  control  has  not  received  a  call  for  heat  from  a  tank  thermostat  or 
tank sensor. 

ON

 

The control has received a call for heat from a tank thermostat or tank 
sensor. 

WHR PUMP: OFF

 

The control has not received a DHW call for heat and has not powered 
the primary pump. 

ON

 

The  control  has  received  a  DHW  call  for  heat  and  has  powered  the 
primary pump. 

DELAY

 

The  DHW  call  for  heat  has  been  satisfied  and  the  primary  pump  is 
running for a fixed time to remove any residual heat. 

Press the Next ► arrow key on the SMART SYSTEM display to access Screen 6. 

6

 

NOT USED: N/A

 

Not used. 

0-10V IN: **.VDC

 

The  control  will  display  a  0-10Vdc  signal  received  from  a  Building 
Management System (BMS) connected to the unit. 

Press the Next ► arrow key on the SMART SYSTEM display to access Screen 7. 

7

 

Cas: Off 

The Master control has been turned off by the 

Enter/Reset 

button on the 

Smart System display. 

Cas: Standby 

The Master water heater has not received a call for heat from a remote 
thermostat. 

Cas: 61.4C (65) 

The Cascade is now active.  The system temperature will be displayed.  
The Cascade set point will be displayed in brackets. 

Cas: Setpoint Met 

The  Cascade  has  met  the  water  temperature  set  point,  but  is  still 
receiving a call for heat from a tank sensor. 

Cas: No Members 

The Master control could not detect any Member controls to participate 
in the Cascade. 

PMP: Off 

The Master control has not received a call for heat from a tank sensor 
and has not powered the primary pump. 

PMP: On 

The Master control has received a call for heat from a remote thermostat 
and has powered the system pump. 

PMP: Delay 

The tank call for heat has been satisfied and the tank pump is running for 
a fixed time to remove any residual heat. 

Press the Next ► arrow key on the SMART SYSTEM display to access Screen 8. 

8

 

Cas Pow: ***% ***% 

The first percentage shows the firing rate that is being sent to the last 
water heater called on.  The second percentage shows the total power 
available to the Cascade. 

Present: 01234567 
 

Example: 

 
Present: 23----01 

Shows  the  number  of  water  heaters  connected  to  the  Cascade.    The 
Master is designated as 0.  Members will be designated 1 - 7.  If a “-“ is 
used in place of a number, that water heater is either not connected, or 
in a lockout mode and not available for the Cascade.  If the number is 
flashing, then that water heater is providing heat to the Cascade.  As the 
lead  water  heater  is  changed  from  day  to  day,  that  water  heater’s 
address  will  be  shown  first  in  the  string  of  numbers.    In  the  example, 
water  heaters  0  -  3  are  present  and  water  heater  2  is  the  lead  water 
heater. 

Press the  Next ► arrow key on the SMART SYSTEM display to roll back to Screen 1.  At any point  if you wish to 
access an earlier screen, press the Previous ◄ arrow key on the SMART SYSTEM display. 

 

 

 

Summary of Contents for EKW115CE













Reviews: