background image

 

Installation & Operation 

Manual

Models:  1000 - 1500

This manual must only be used 
by a qualified heating installer 
/ service technician. Read all 
instructions, including this manual 
and the Armor X2 Water Heater 
Service Manual, before installing.  
Perform steps in the order given.  
Failure to comply could result in 
severe personal injury, death, or 
substantial property damage.

 WARNING

Save this manual for future reference.

AWX2-I-O Rev F

-- This water heater MUST NOT be installed in 
any location where gasoline or flammable vapors 
are likely to be present.

--  WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.
• Do not touch any electric switch; do not use any 
  phone in your building.
• Immediately call your gas supplier from a near by 
  phone.  Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire 
 department.
• Installation and service must be performed by a 
 qualified installer, service agency, or the gas 
 supplier.

 WARNING:  

If the information in this 

manual is not followed exactly, a fire or 
explosion may result causing property damage, 
personal injury or loss of life.

LOW LEAD CONTENT

Summary of Contents for Armor X2 AWL1500





































































Reviews: