Lochinvar 140H Installation Manual And Owner'S Manual Download Page 58

Page: 58 / 76

Page

PROBLEM

SOLUTIONS

BUIL

T-

ONTR

OLLER

AND

REMO

ONTR

OLLER

Controller does not

display anything when

the power button is

turned on.

• Make sure the unit is supplied with power.

• Make sure the connection to the unit is correct. (pp. 36 and 37)

NOTICE:

When the unit has not operated for five minutes or more, the display of the

controllers turns off to conserve energy.

When the

controller turned

ON, STAND BY LED

is lit.

Built-in controller

Although the controller of the parent unit will

display the set temperature at

the Easy-Link System, the controller of the child unit will not display the set

temperature.

An ERROR code is

displayed.

• Please see pp. 58 to 61.

EAS

Y-LINK

STEM

540H

model

only

How are the unit

numbers assigned?

• For an Easy-Link System, the Parent unit is always labeled #1 and all other

subsequent Child units are numbered randomly.

• To check which numbers are assigned to which Child units, push the

increase button on the computer board of any Child unit as shown below.

The unit number will be displayed on the temperature controller of the

Child unit and/or the remote controller of the Child unit, if installed. (Refer

to pp. 38 and 39.)

Increase button to check

unit number

Troubleshooting

Owner's Guide

ERROR CODES

• The units have self-diagnostic functions for safety and convenience when troubleshooting.

• If there is a problem with the installation or the unit, the error code will be displayed on the built-in

controller and remote controller. The green LED on the computer board will flash in a pattern shown on the

next page.

• Consult the table on the following pages for the description of each error code.

Error code indicator on the built -in

temperature controller

Error code indicator on the remote

controller

Error code on the computer board

Indicated by 1/2-second flashes on the Green LED.

140H/240H/340H

Green LED

540H

Green LED

Summary of Contents for 140H













































































Search results

Summary of Contents for 140H

Reviews:

Related manuals for 140H

Brands by name

Popular brands

Lochinvar 140H, Installation Manual And Owner'S Manual

Search results

Summary of Contents for 140H

Reviews:

Related manuals for 140H

Brands by name

Popular brands