3
EN-33.C.14.3-6.0501
Channel 1
Channel 2
Channel 3
Channel 4
Reset P
ower
Cq
Antenna holder to be
placed on the wall
a minimum of
200 mm from
metal objects
Antenna hold
er
160 mm
25 mm
Activating the receiver
For Cq 4 and Cq 6 as follows:
• To activate the memorizing phase on the receiver unit,
press the button for the channel that is to be activated
Þ
rst. A weak sound signal is heard and the indicator
light will come on.
For Cq 1 as follows:
• To activate the memorizing phase on the receiver unit,
press the button . A weak sound signal is heard
and the indicator light will come on.
Activating the room thermostat
• Press and hold the lower black button (B).
• Brie
ß
y press the upper black button (C).
• When the indicator light (D) is lit, release the lower
button. Memorizing (the connection) between the
thermostat and the channel selected now occur. Pay
attention to the receiver. Once contact is established,
the sound signal will cease and the indicator light will
go
out.
• Press the upper button on the room thermostat one
more time to switch off the indicator light. (The indicator
light on the thermostat in future use is only used to
warn of low battery power.)
Function control
Place the room thermostat in the room where it is intended
to be assembled according to the design. By turning the
thermostat’s adjustment dial, the indicator light on the
receiver’s channel will be lit or switched off respectively
within approximately 30 seconds.
• Dial towards maximum temperature, the light on the
receiver unit comes on.
• Dial towards minimum temperature, the light on the
receiver unit goes off.
NB: The receiver Cq 1 works the opposite way.
If the light switches off when it should come on, check
that the mains switch’s setting is in the lower position
towards the heat symbol. See the section LK Room
Thermostat Cq. If the setting was right and the problem
continues, see the section ”Heat/Cool”.
NB: During set up (only) the indicator light on channel
4 or channel 6 comes on when one or more other
channels trigger the heating. This function continues
until all the channels are activated. For more informa-
tion, see the section “Pump Control”.
ADDITIONAL MEASURES
Assembling the room thermostat
Open the room thermostat by pulling the temperature scale
dial right out and loosening the screw that becomes visible.
Bend out the upper part to the left until it becomes loose.
Position the room thermostat as per the design plan.
For the room thermostat to function properly, the fol-
lowing guidance should be followed:
• Mount it on an inner wall where it is ventilated but not
in a draught. (NOTE FOR UK: in some home refurbish-
ment projects where the building is poorly insulated, it
may be prudent to place the thermostat on an outside, or
coldest, wall. The thermostat will then compensate by
calling for heat.)
• Do not expose it to direct sunlight or other heat sources.
• Mount it approximately 1.5 metres above the
ß
oor.
• Do not mount it near a radio, TV or other transmitter.
• Do not mount it near metal objects, such as metal doors,
metal cupboards or similar.
Completing activation / memorizing
Continue activation / memorizing in the same way as for
the other channels, following the instructions for the
LK Room Thermostat Cq.
LK Antenna Cq
The LK Antenna Cq is intended to be used when the radio
connection between the room thermostat and the receiver
unit is unsatisfactory.
The antenna is assembled as follows:
• The antenna holder is supplied with self-adhesive tape
and is attached to the top of the receiver unit. The
stripped part of the antenna is pulled through the
antenna holder until it appears on the other side.
• The other end of the antenna is pulled to the outside
of the enclosure and is assembled in the same way,
placed at least 200 mm from any metal objects.
!
