CATALOG # :
L I G H T I N G
INSTALLATION INSTRUCTIONS
5461 W. Jefferson Blvd. Los Angeles, CA 90016
•
P. 800-515-4880
•
F. 800-972-4880
•
www.liton.com Product specifications subject to change without notice.
SAVE THESE INSTRUCTIONS
Keep these instructions in a safe place for future use/reference.
Page 3 of 5
LCALDJ2 Track Mount with Single (1CCT) or Dual (2CCT) Circuit Track
01182019
Important: Please read and understand all instructions
completely before installing this fixture.
WARNING: Fixture installation (and use) and all electrical connections must be in accordance with
local and National Electrical Codes (N.E.C.) rules, regulations and standards. If you are unfamiliar
with installing fixture(s), accessories and/or electrical wiring have a qualified licensed electrician
install this fixture for you. Fixture should be installed by a qualified electrician.
WARNING: RISK OF SHOCK. House electric current can cause painful shock or serious injury.
WARNING: Always disconnect power before fixture installation, wiring, or maintenance.
WARNING: Before starting the wire connections, disconnect the power by turning off the circuit breaker
or removing the fuse at the fuse panel. Turning the power off using the light switch is not sufficient to
prevent electrical shock.
This luminaire must be connected with supply wire/conductors rated at 90°C. Most dwellings built
before 1985 have supply wire rated at 60°C; consult a qualified electrician before installing.
WARNING: Before service insure fixture is cool to touch.
WARNING: Check fixture for input voltage before connecting power to fixture.
WARNING: RISK OF SHOCK. Fixture is suitable for dry locations (unless otherwise stated on fixture,
Liton's web site or other installations. Also for use with covered ceiling mount.
WARNING: Do not install any fixture or assembly (etc.) closer than 6" from any curtain, or similar
combustible material.
Fixture must be installed on a circuit protected by Ground Fault Circuit Interrupter
(GFCI).
Fixtures that are not LED:
For installing lampholder, make sure to refer to other instructions within your fixture, as
required. For installing lamps please refer to your lamp manufacturers’ instructions.
LED Fixtures:
RELAMPING:
Return fixture to Liton for servicing/replacing LED and LED drivers, as required.
Install LED fixture(s)/LED driver(s) only on their own circuit. Do not mix any other
products (Incandescent, Compact Fluorescent, H.I.D. products/fixtures, etc...) with LED
fixture(s)/LED driver(s) on a single circuit.
Do not use any other electrical equipment (example: surge protector photocell, etc.) that
is not (rated) for use with LED fixture(s)/LED driver(s) on the same circuit as LED
fixture(s)/LED driver(s).
Install remote surge protector(s) (by others, goes on the circuit with nothing between the
surge protector and the LED fixture(s)/LED driver(s)), if the fixture is not already
installed with a surge protector, to help remove power surges that may harm LED
fixture(s), appropriate for the installation. Periodically check and make sure that your
remote surge protector(s) are in good working order.
FIG. 2
FIG. 3
FIG. 1
Components/Parts LPTM4 Track Mount w/ Single Circuit Track(1CCT) or Dual Track (2 CCT)
Tools Required
• No tools
required.
• For single
and dual
circuit track
parts
installation
see Track
Installation
instructions.
LPTM4: TRACK MOUNT (CONNECTED TO FIXTURE)
(in Lower Position - P1) (1) (For use with Single or
Dual Circuit Track)
NO Busbar Stopper
Busbar
Stopper
Ground Connector
(GND)
Neutral (N)
Power (P1)
(Lower
Position)
Neutral
(N)
Ground
(GND)
Power (P1) (Lower)
Neutral (N)
Ground (GND)
Polarity Line
Power (P2)
(Upper)
Power (P1)
Neutral (N)
Ground (GND)
Polarity Line
Track
Polarity
Line
Contact Connector
Power (P1)
(Lower Position)
Ground Connector (GND)
Polarity Line (Track)
Locking
Lever
(Track Mount
Outside)
NOTE: Turn Track Mount
1/4 turn (90°) so Ground
Connector is on the
same side of the Track as
the Track Polarity Line.
LPTM4: TRACK MOUNT
(In Upper Position - P2.
For use with only Dual
Circuit Track)
Contact Connector Power (P2)
(Upper
Position)
WARNING: DO NOT
USE Connector or
End Cap without
Busbar Stoppers!
End Cap
NO... X
DUAL CIRCUIT TRACK (2 CCT TRACK CHANNEL)
SINGLE CIRCUIT TRACK (1 CCT TRACK CHANNEL)
YES ... O
End Cap
(with 1 Neutral)
(with 1 Neutral)
SINGLE and DUAL CIRCUIT TRACK AND PARTS (ORDERED SEPARATELY).
NOT ALL PARTS SHOWN FOR CLARITY
FIXTURE INSTALLATION
WARNING: Use only Liton Track parts (see above and FIG. 1 and 16) with LPTM4 Track Mount (connected to fixture). Do
not use Liton Track LPTM4 Track Mount with any other manufacturers track (system, parts, etc.).
WARNING: To avoid the potential risk of fire and shorting, you should not under any circumstances use the connectors
and end cap without Busbar Stoppers (see above picture with "NO...X" mark) for your track system!
WARNING: Always disconnect power before fixture installation, wiring, or maintenance.
1. Install Liton’s Track as per Track Installation Instructions.
2. Note which Liton track type is installed, Single Circuit Track (see FIG. 1) or Dual Circuit Track (see FIG. 2).
CAUTION: Before Installing Track Head in track, make sure power contact conductor is in the right position!
3. When using Single Circuit Track (see FIG. 1 left) make sure the Track Mount "Power" contact connector location is
in the Lower Position - P1 (see above left). When using Dual Circuit Track (see FIG. 2 left) make sure the Track Mount
"Power" contact connector location is either in the Lower position - P1 (see above left) for the Track P1 lower circuit
(see FIG. 1) or in the Upper position - P2 (see above) for the Track P2 upper circuit (see FIG. 2). As needed push up
or down on the Track Mount "Power" contact connector to put connector in the P1 or P2 position. For the Dual Circuit
Track each circuit is rated for 2400 Watts and will allow you to control two individual sets of fixtures.
4. Locate the Track Polarity line and the Ground Connector on the and LPTM4 Track Mount (see above left and FIG. 2
and FIG. 3).
5. Pull down on the Track Mount locking lever and insert the Adapter Contacts in the Liton Single or Dual Circuit Track
slots (see FIG. 3).
6. Rotate Track Mount LPTM4 one quarter (1/4) turn (90 degrees) so that the Track Mount Ground Connector (side
of Track Mount with two contacts) is on the same side of the track as the Track polarity line (see FIG.17) and locking
lever locks back in place. Do NOT rotate Track Mount Ground to the side of the track without the Polarity Lines. Make
sure track lock in place.
7. To remove fixture pull down on the locking lever and rotate 1/4 turn (90 degrees).
When using LPTM4 Track Mount contact connector in Lower Position (P1, see above) with Dual
Circuit Track (see above) the power comes from POWER (P1). If using LPTM4 Track Mount
contact connector in Upper Position (P2, see above center) with Dual Circuit Track the power
comes from POWER (P2).
(Fixture not shown for clarity)
Use the LPTM4 Track Mount contact connector only in the Lower Position (P1, see above) with
Single Circuit Track (see above). The power comes from POWER (P1).