manualshive.com logo in svg

Lithium Grim Sultan of Tone, Building Instructions, Page: 2 / 12

Share
Download
Lithium Grim Sultan of Tone Building Instructions Download Page 2

Sultan of Tone v4.1  

 

 

2 

Table of contents 
 

Components ............................................................................................................................................ 3 

Bill of Materials ....................................................................................................................................... 4 

PCB layout ............................................................................................................................................... 5 

Power section .......................................................................................................................................... 6 

Building sequence ................................................................................................................................... 7 

Modifications ........................................................................................................................................... 8 

Off board wiring and drilling ................................................................................................................... 9 

Diode switch settings ............................................................................................................................ 10 

Troubleshooting .................................................................................................................................... 11 

Schematic .............................................................................................................................................. 12 

 

 

 

Read this entire manual thoroughly before you start to building the effect! Especially the 
Modification and Power section part. Decide before building the effect which mods you want to try 
so that you do not need to desolder parts later. 

Last update: 28-09-2017 

Summary of Contents for Sultan of Tone













Reviews:

No comments