Lithium Grim Klonulator Building Instructions Download | Manualshive

Page: 10 / 18

background image

Klonulator v1.0

Manufacturers and product names are mentioned solely for circuit identification, and where applicable their trademarks are the
property of their respective owners who are in no way associated or affiliated with the author. No cooperation or endorsement

is implied.

10

Switches

Gain boost

Clipping diodes

If you want to be able to switch the diodes externally and not via the internal DIP switch, then leave
out the DIP and wire it like this using a SP3T (ON/OFF/ON) switch:

Or as a DP3T On/Z/On switch so you can also switch all diodes on (but not off!) Test the pole that are
active in the middle position before you solder it.

«
...
8
9
10
11
12
...
»

Summary of Contents for Klonulator



















Reviews:

No comments

Related manuals for Klonulator

F-13 Neo Flanger

Brand: Alexander Pages: 2

Brand: DOEPFER Pages: 21

Compact 6.2 D2320

Brand: DAPAudio Pages: 16

RackConsole-PRO 17HR

Brand: G&D Pages: 16

Brand: Effectrode Pages: 4

Brand: Ferlabel Pages: 12

Brand: Yamaha Pages: 4

Brand: Yamaha Pages: 2

Brand: Yamaha Pages: 16

Brand: Yamaha Pages: 16

Brand: Yamaha Pages: 16

Brand: Yamaha Pages: 2

Brand: Yamaha Pages: 20

Brand: Yamaha Pages: 20

Brand: Yamaha Pages: 22

Brand: Yamaha Pages: 23

Brand: Yamaha Pages: 21

Brand: Yamaha Pages: 34

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands