background image

3. Installation Preparation.

4. Hanging Bracket Installation.

page 3

ON

OFF

ON

OFF

j-hook

hanging bracket

This fan can be mounted with a 

downrod

on a normal ceiling only. Fan 

cannot

 be mounted 

with flushmount installation 

nor

 on a vaulted 

ceiling.

Installation requires these tools:

Phillips screwdriver, flat-head screwdriver, 
adjustable pliers or wrench, stepladder, wire 
cutters, and rated electrical tape.

12f

t.

  - 15f

t.

12ft.  - 15ft.

(3.66m  - 4.57m)

(3.66m  - 4.57m)

10 feet

(3.05m)

(76cm)

30 

inches

To prevent personal injury and damage, ensure 
that the hanging location allows the blades a 
clearance of 10ft. (3.05m) from the floor and 30in. 
(76cm) from any wall or obstruction. 
This fan is suitable for room sizes up to 225 
square feet (20.9 square meters). 

Turn off circuit breakers to current fixture from 
breaker panel and be sure operating light switch is 
turned to the OFF position. 

WARNING: 

Failure to disconnect power supply prior 

to installation may result in serious injury.

Remove existing fixture. 

WARNING:

 When using an existing outlet box, be 

sure the outlet box is securely attached to the 
building structure and can support the full weight of 
the fan. Ensure it is clearly marked "Suitable for Fan 
Support." If not, it must be replaced with an approved 
outlet box. Failure to do so can result in serious injury.

CAUTION

Be sure oulet box is grounded properly 

and that a ground wire (green or bare) is present.

Install hanging bracket to outlet box using original 
screws, spring washers and flat washers  provided 
with new or original outlet box.

Install rubber 

cushions (if not already pre-attached to hanging 
bracket) between outlet box and j-hook hanging 
bracket to reduce vibration of metal to metal 
surfaces. Arrange electrical wiring to the front or 
back side of the hanging bracket.

*Note

It is very important that you use the proper 

hardware when installing the hanging bracket as this 
will support the fan. 

spring washers

outlet box screws

flat washers

downrod

installation

CANNOT be
installed on
angled or
vaulted ceilings

flushmount

installation

blade edge

rubber cushions

Summary of Contents for E-UB48BC4C1










Reviews: