to the fade time. Release the “Power” button to lock in the fade time.
“Aaaaand Action!” Cueing
: After setting the fade time, this dimmer function
allows for the LiteRibbon to be brought up on cue.
From STANDBY:
Set the fader to the desired brightness. Press and hold the
“Power” button until the cue is given. When the cue is given, release the “Power”
button, and the LiteRibbon will fade on (with the set fade time) to the desired
brightness.
From ON:
With the fader set to the desired brightness, press and hold the “Power”
button until the cue is given. When the cue is given, release the “Power” button,
and the LiteRibbon will fade off (with the set fade time).
Troubleshooting
If LiteDimmer Micro Single stops operating, remove it from the circuit to confirm
that the dimmer is the problem. Connect the LiteRibbon directly to power. If it does
not operate, the problem may not be the dimmer. Check leads and connectors. If
the LiteRibbon does operate, LiteDimmer Micro Single could be overheated due to
over-current conditions or is damaged. If damaged, contact the LiteGear Service
department for service.
If LiteDimmer Micro Single seems to be experiencing irregular operation, a factory
reset may be needed. Resetting the operating system can restore normal operation
in many cases. To perform a factory reset, disconnect your dimmer from power,
and bring the fader down to 0. Next, press and hold the “Power” button, and then
power the dimmer.
After powering the dimmer, release the “Power” button. (The “Power” button should
now be flashing on and off.) With your fader still at 0, tap the “Power” button once
to confirm that you wish to reset the dimmer. At this time, cycle the power. Note
that your preferences and settings may now have to be reset. (The “Power” button
should now be flashing the software version of your dimmer.)
As an added convenience for mounting, the LiteDimmer Micro Single
EFX Paparazzi features a magnetic base. An adhesive-backed metal
plate accessory is included.
Warnings
Stage and Studio Use Only • Dry Location Only • Hazardous Voltage
Risk of Electrical Shock • Disconnect Power Before Servicing • Not For Residential Use
Any questions? Comments? Concerns?
Contact us at +1 818.358.8542 or [email protected].
+1 (818) 358-8542 • [email protected] • www.litegear.com
Technical Specifications
SIZE: 4 in. x 1.625 in. x 1.125 in.
WEIGHT: 0.146 lb, 2.336 oz, 66 g
INPUT: 12/24V DC, (9-24V DC); input voltage must match load voltage requirements!
RATING: 4 amps max. total
WATTAGE: 96 watts max. total at 12VDC; 192 watts max. total at 24VDC.
CONNECTOR: Barrel, 2.1 mm x 5.5 mm
OUTPUT: DynaRythmic PWM; does not provide “current limiting.”
For use with LiteGear products only.
Male Barrel Connector
POWER INPUT
Wrist Strap
Mounting
Screws for
LiteMat 1
Lighted
Power
Button
Rigging
Points
Wrist Strap/
LiteMat 1
Mounting
Notch
LiteMat 1 Mount
Notch
Attach
Wrist Strap
as shown.
ACCESSORIES
Can be
attached to
LiteMat 1 using
provided screws.
© 2017 LITEGEAR, INC. All rights reserved.
LiteRibbon® is a registered trademarks of LiteGear, Inc.
© 2017 LITEGEAR, INC. All rights reserved.
LiteGear™, LiteMat™, LiteStix™, LitePower™, LiteDimmer™, LiteEFX™,
and E-Control™ are trademarks of LiteGear, Inc.
Female Barrel
Connector
LED OUTPUT
Fader
Brightness
Control
