background image

Operating your Pirate Ship with TrainMaster Command Control

W

ire your accessory with an SC-2 Switch and Accessory Controller (available separately, 
6-22980) or the Accessory Switch Controller (available separately, 6-14182). Refer to

these manuals for additional information.

Be sure that the ON/OFF switch is in the ON position. Refer to Figure 2 on page 4 for
the location of that switch.

SC-2 wiring and operation

Three wires (not included) are needed to connect your Pirate Ship to the SC-2 and a separate
accessory transformer. We recommend using 22 gauge wire.

1.  Attach one wire to the transformer Common/Ground/U terminal and

connect it to the accessory COMM (common) position on the SC-2. 

2. Connect one of the Pirate Ship terminals to the accessory ON/OFF toggle

position on the SC-2. 

3. Finally, connect the remaining Pirate Ship terminal to the transformer

Power/A terminal. 

Use the AUX2 button on your CAB-1 Remote Controller to toggle the Pirate Ship ON and OFF.

5

ACC2

ACC2

ACC1

ACC1

POWER

SUPPLY

Common/Ground/U

Common/Ground/U

Power/A

Power/A

Figure 3. SC-2 connections

Note!

Summary of Contents for Pirate Ship Ride









Reviews: