Lionel Midwest FreightReady-to-Run Set Owner'S Manual Download Page 9

Running your train

9

Transformer functions

A

s you turn the throttle control knob to the right, power to the track is increased. Figure 5
illustrates the throttle control knob settings. When the indicator reaches the green band,

there should be sufficient power to operate the locomotive. The further into the green area the
knob is turned, the faster your train will go. Remember that the greater the load on the engine
(adding more cars for the engine to pull, for example), the farther into the green area the
knob must be turned before it will operate the locomotive.

The yellow band indicates the average power range that the train will be operating in. The

red band represents maximum power output.

FULL

FULL
SPEED

SPEED

OFF

OFF

R

FULL
SPEED

OFF

FULL
SPEED

OFF

Press the HORN button to
produce a realistic diesel
horn sound.

Press the DIRECTION button
to go forward or reverse, or to
place the locomotive in neu-
tral (no movement, headlight
is on).

Turn the throttle control knob
to the right for more power.

The LED indicator
shows when your
controller is ON.

Green band

Yellow band

Red band

A slight increase in speed
during horn operation is
normal.

Figure 5. Transformer operation

Summary of Contents for Midwest FreightReady-to-Run Set

















Reviews: