background image

operating your Powermaster Bridge safely

When using electrical products, follow these basic safety precautions:

•  Read these instructions thoroughly before using this device.
•  The PowerMaster Bridge is not recommended for children under fourteen years of age.
•  Parents should periodically inspect the PowerMaster Bridge for potential hazards and have 

them repaired by an authorized Lionel Service Center. In the event that such a condition 
exists, the PowerMaster Bridge should not be used until it has been properly repaired.

•  The PowerMaster Bridge is intended to be used indoors. Do not use the PowerMaster Bridge 

if water is present. Serious or fatal injuries may result.

•  Do not use the PowerMaster Bridge for anything other than its intended purpose. This unit 

was designed to operate with the Lionel LEGACY Control System.

•  The PowerMaster Bridge was designed to operate on 120-volt, 60-Hz power. Do not connect 

the PowerMaster Bridge to any other source of power.

•  Do not operate the PowerMaster Bridge with a damaged cord, plug, or case.
•  To avoid the risk of electrical shock, do not disassemble the PowerMaster Bridge. There are 

no user-serviceable parts inside. If damaged, take the unit to an authorized Lionel Service 
Center. See page 8.

•  Unplug the PowerMaster Bridge from the power source when not in use.

Do not operate your railroad unattended. Obstructed accessories or stalled trains 
may overheat, resulting in damage to your layout.

Caution!

The following Lionel marks may be used throughout this instruction manual and are protected under law. All 
rights reserved.

Lionel

®

, TrainMaster

®

, Odyssey

®

, RailSounds

®

, CrewTalk

, TowerCom

, DynaChuff

, StationSounds

Pullmor

®

, ElectroCoupler

, Magne-Traction

®

, CAB-1

®

 Remote Controller, PowerMaster

®

, Lionel ZW

®

, ZW

®

PowerHouse

®

, TMCC

®

, Lionelville™, Lockon

®

, Wireless Tether

, LionMaster

®

, FatBoy

, American Flyer

®

TrainSounds

, PowerMax

, LEGACY

, PowerMax

 Plus, Odyssey II

, LEGACY RailSounds

The name FasTrack

®

 is used with permission from Pitsco, Inc.

Warning!

Meijer.com

Summary of Contents for 996 PowerMaster Bridge









Reviews: