background image

9

Connecting the speakers

The LK240 comes equipped with four pairs of speaker output

sockets to allow bi-wiring, or even tri-wiring. Alternatively, auxiliary

speakers may be connected.

The type of speaker socket on your LK240 will depend on the

market it was manufactured for. If European, the socket will be a

high contact pressure binding post suitable for connecting with

bare speaker wire. If American, the socket will be suitable for

banana type connectors.

Operation

To turn on the LK240 amplifier, press the power switch on the front

panel.

Signal detector sensitivity

The LK240 uses signal sense circuitry to detect the presence of an

audio input signal. As soon as the LK240 detects the presence of

an audio signal, it will power up and a small indicator light adjacent

to the power switch will light green. Whenever an audio signal is

removed, the LK240 powers down to standby mode after a short

delay until it again detects an audio signal. The small indicator light

will turn red when the LK240 switches to standby mode.

Adjusting the signal detector

The LK240 is shipped with signal sense circuity set to maximum

sensitivity for normal operation. However, if you find that

interference or other audio noises in your system cause the LK240

to power up, you may wish to decrease the sensitivity of the signal

detector. To do this turn the signal detector sensitivity control on

the back panel anticlockwise towards the minimum position.

Summary of Contents for LK240























Reviews: