Quick Reference Sheet
Applicable models: LKV-9304 / LKV-9308 / LKV-9316
Notes:
1. OSD Menu control is only available when the OSD menu is activated on the screen. To activate the OSD menu, use the hotkey sequence ScrLk + ScrLk +
(Space Bar)
. For detailed OSD operation
reference, please refer to the
User Guide. When OSD Menu is active, the mouse will be locked until the OSD Menu is off.
To reset OSD menu to default, just use a pointed needle to press the recessed
opening (without marking) just beside the DC jack on the back panel for several seconds.
2. Note that
a
,
b
,
y
and
z
each
denotes a number key. (ab) = 01 ~ 16 ; (yz) = 01 ~ 08. For example, ScrLk + ScrLk + 03 + 06 is for bank 3 port 6. When using a single KVM Switch configuration, the default
bank no. is 01, therefore hit ScrLk + ScrLk + 01 + 12 for port 12 for a single KVM Switch configuration.
3. The password is up to 8-character length. You should remember the password since it is required for access to your KVM switch once you enable the password protection for your KVM switch.
However, if you forget the password and thus are blocked from KVM access, you should contact Linkskey for technical support.
Technical Support
E-mail: [email protected]
Rev.1.2 Copyright© All rights reserved. June 2006
Website: www.linkskey.com
Quick Reference Sheet
QUICK REFERNCE SHEET for KVM Switch Operation Commands Hotkeys/ OSD Menu / Front-Panel Buttons
Command
Hotkeys
OSD control
1
Front-panel
Description
Select Computer
ScrLk + ScrLk +
(a) + (b) + (y) + (z)
(
ab = bank no. ; xy = channel no.
)
2
Cursor keys to navigate
Enter to select
Press corresponding button yz on Switch
ab for channel yz on bank ab.
Select the active bank (switch) and channel
Next lower channel
ScrLk + ScrLk +
↑
(arrow up)
Cursor keys to navigate
Enter to select
Press corresponding button
Select the next lower connected channel
Next higher channel
ScrLk + ScrLk
+ ↓ (arrow down)
Cursor keys to navigate
Enter to select
Press corresponding button
Select the next higher connected channel
Next lower bank
ScrLk + ScrLk + PgUp
PgUp (w/ OSD Menu)
Press corresponding button on that
switch
Select the next lower bank (switch) when
with multiple daisy-chained units
Next higher bank
ScrLk + ScrLk + PgDn
PgDn (w/ OSD Menu)
Press corresponding button on that
switch
Select the next higher bank (switch ) when
with multiple daisy-chained units
Autoscan Beep Sound
On/Off
ScrLk + ScrLk + B
--
--
Toggle on/off the beep sound for switching
confirmation while autoscanning
Load Factory Default
--
Main Menu / Setup / Load
Default
--
Restore the EEPROM settings to the factory
default
Change Computer Name
--
Cursor keys to navigate
Enter (Ins) to select/edit
--
Change the computer name
[max. length = 8 alphanumeric characters]
Reset / Initialize KVM
(whole daisy-chain)
ScrLk + ScrLk + End
--
--
Reset the KVM Switch / initialize the daisy-
chain setup
Show OSD Menu
ScrLk + ScrLk +
(Space Bar)
--
--
Activate the OSD Menu on the console screen
Autoscan
ScrLk + ScrLk + S
--
--
Autoscan through every connected channel
for quick screen browsing of each channel.
Stop Autoscan
Any key
--
Press any push button
Terminate Autoscan activity
Autoscan Period
[5 ~
10
~ 95 seconds]
--
Main Menu / Setup / Autoscan
period
--
Specify delay time within a range of 5 ~ 99
seconds [default = 10 sec ]
Auto Logout Timeout
Enable/Disable
[
0
~ 99 min ]
--
Main Menu / Setup / Auto
Logout
--
Specify the time out for auto logout -- screen
/keyboard/mouse locked after timeout
period for security. (default = 0 = Disable)
OSD Menu Timeout
[0 ~
60
~ 95 seconds]
--
Main Menu / Setup / OSD
Timeout
--
Specify the timeout for OSD menu
[default = 60 seconds; 0 = disable]
OSD Title Bar On/Off
[
ON
/OFF]
ScrLk + ScrLk + T
--
--
Enable/disable the OSD Title Bar
[default = ON]
OSD Title Bar Position
[
Left
/Right]
--
Main Menu / Setup / Title Bar
Select the OSD title bar position on your
screen
Setup Password
3
[
Disable
/Enable]
--
Main Menu / Setup / Setup
Password
--
Enable/disable password protection
[default == Disable; password length <= 8
characters]
