liniLED PCB Photon 1200 Manual Download Page 15 | Manualshive

Page: 15 / 20

background image

15

LED strip manual | liniLED® Top Photon 1200

Firmly grab the outer shell and gently grab the liniLED® LED strip.

Gently wiggle the connector and pull in opposite direction.

The connector should look like this when it is removed.

Firmly press the sides of the shell and pull gently while holding the

cable to remove it.

Article number Description

11200

liniLED® Top Connector set 1 m

11201

liniLED® Top Connector set 5 m

11208

liniLED® Top Extension Cord

Uninstalling the connector

5

3

2

4

1

«
...
13
14
15
16
17
...
»

Summary of Contents for PCB Photon 1200





















Reviews:

No comments

Related manuals for PCB Photon 1200

Brand: Lighting Technologies Pages: 22

Brand: S:FLEX Pages: 37

Brand: Gainsborough Pages: 3

Brand: Vaughan Pages: 4

Brand: easymaxx Pages: 6

Brand: Quoizel Pages: 6

Brand: CALIMA Pages: 9

Brand: Sealite Pages: 16

Brand: WE-EF Pages: 7

Streetworks SDL LED Arm Mount

Brand: Eaton Pages: 7

Brand: WE-EF Pages: 7

Brand: ALS Pages: 2

Brand: WAC Lighting Pages: 2

Brand: smart & green Pages: 5

Brand: REV Ritter Pages: 20

Brand: Pro-Elec Pages: 2

Brand: Pro-Elec Pages: 2

Brand: Optimum Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands