Linear VS-GSWG, Installation Manual, Page: 19 / 34

VS-GSWG Swing Gate Operator Installation Guide
- 17 -
P1250 Revision X6 7-8-2011
Advanced Controller Programming (Cont.)
Radio Transmitter Learn
The Controller’s built-in MegaCode® radio receiver can store the IDs of
up to 40 transmitters. Refer to the fi gure for the steps required to learn
transmitters.
✓
NOTE: This function will NOT be displayed if the transmitter memory
is full, or if the radio receiver is disabled.
Radio Transmitter Delete
Transmitters can be deleted from the Controller’s memory either
individually, or all at the same time. Refer to the fi gure for the steps
required to delete transmitters.
✓
NOTE: This function will NOT be displayed if no transmitters are
stored in memory, or if the radio receiver is disabled.
MGT Obstacle Transmitter Learn
The Controller supports one or two Model MGT Obstacle Transmitters.
The transmitters can be programmed to function as Open Obstruction,
Close Obstruction, Reverse, or Stop. Refer to the fi gure for the steps
required to learn MGT transmitters.
✓
NOTE: This function will NOT be displayed if two MGT transmitters
are already stored in memory, or if the radio receiver is disabled.
MGT Obstacle Transmitter Delete
MGT transmitters can be deleted from the Controller’s memory either
individually, or all at the same time. Refer to the fi gure for the steps
required to delete MGT transmitters.
✓
NOTE: This function will NOT be displayed if no MGT transmitters are
stored in memory, or if the radio receiver is disabled.
Motor Type Selection
The factory sets the default for the Controller to match the type of motor in
the operator. If required, change the motor selection option to a different
type of motor used in the operator. The options available are:
• AC Motor Only
• DC Motor Only with Mechanical Braking
• DC Motor with Electronic Soft Start/Stop
• 3 Phase AC Motor
• AC Motor with DC Motor Backup with Mechanical Braking
• AC Motor with DC Motor Backup with Electronic Soft Start/Stop
Reset Controller to Factory Defaults
The Controller can be reset with this function. ALL PROGRAMMED
DATA WILL BE LOST , and the factory defaults will be loaded. This
function will not erase radio transmitters, current sense values, or motor
type. Transmitters must be deleted with the two functions above.
FUNCTION
TO DELETE ALL M G T T R AN S MITTE RS , P R E SS ENTE R FO R
2 S ECOND S , (TO EXIT WITHOUT DELETIN G ANY, QUICKLY
P R E SS ENTE R )
ERASE MGT
TRANSMITTERS
"MD" WILL B LINK FO R 3 0 S ECOND S WHILE THE CONT R OLLE R
I S R EADY TO DELETE ALL M G T T R AN S MITTE RS
"MD"
ENTER
P R E SS ENTE R
ENTER
THE DI S PLAY WILL S HOW "DELETE ALL" AND THE
CONT R OLLE R R ETU R N S TO P R O GR AMMIN G MODE
FUNCTION
TO DELETE ALL T R AN S MITTE RS , P R E SS ENTE R FO R
2 S ECOND S , O R TO PICK T R AN S MITTE RS G O TO NEXT S TEP
DELETE
TRANSMITTERS
"TD" WILL B LINK FO R 3 0 S ECOND S WHILE THE CONT R OLLE R
I S R EADY TO DELETE ONE O R MO R E T R AN S MITTE RS ,
(TO EXIT WITHOUT DELETIN G ANY, P R E SS ENTE R )
"TD"
ENTER
P R E SS ENTE R
ENTER
O R
UP DOWN
ENTER
P R E SS UP O R DOWN TO S C R OLL TH R OU G H THE LI S T
OF T R AN S MITTE R ID NUM B E RS
THE T R AN S MITTE R ID NUM B E R I S DI S PLAYED
(TO EXIT WITHOUT DELETIN G , P R E SS ENTE R )
(TO PICK A DIFFE R ENT T R AN S MITTE R ID, P R E SS UP O R DOWN)
P R E SS ENTE R FO R 2 S ECOND S TO DELETE THE
T R AN S MITTE R DI S PLAYED
FUNCTION
ACTIVATE THE M G T T R AN S MITTE R , THE DI S PLAY WILL
FLA S H " r E" - IF THE T R AN S MITTE R I S AL R EADY ENTE R ED,
"DU" WILL B E DI S PLAYED, IF DECODE I S B AD "E RR O R " WILL
B E DI S PLAYED
LEARN MGT
TRANSMITTERS
P R E SS ENTE R , "ML" WILL B LINK FO R 3 0 S ECOND S WHILE
THE CONT R OLLE R I S R EADY TO LEA R N AN M G T
T R AN S MITTE R
"ML"
ENTER
O R
UP DOWN
ENTER
DI S PLAY WILL S HOW "--" FO R 5 S ECOND S , THEN S HOW THE
T R AN S MITTE R ' S ID NUM B E R - R EPEAT S TEP S FO R
S ECOND M G T T R AN S MITTE R IF U S ED
P R E SS ENTE R TO ACCEPT THE S ELECTION
P R E SS UP O R DOWN TO S ELECT THE M G T FUNCTION :
" r E" = R EVE RS E " S t" = S TOP
"OP" = OPEN O BS T R UCTION "CL" = CLO S E O BS T R UCTION
FUNCTION
ACTIVATE THE T R AN S MITTE R
DI S PLAY WILL S HOW "- -" THEN THE
T R AN S MITTE R ID NUM B E R - IF T R AN S MITTE R
I S AL R EADY ENTE R ED, " d U" WILL B E DI S PLAYED,
IF DECODE I S B AD "E RR O R " WILL B E DI S PLAYED
LEARN
TRANSMITTERS
"TL" WILL B LINK FO R 3 0 S ECOND S WHILE
THE CONT R OLLE R I S R EADY TO
LEA R N A T R AN S MITTE R
"TL"
ENTER
P R E SS ENTE R (ONCE FO R EACH T R AN S MITTE R ,
UP TO 40 T R AN S MITTE RS TOTAL)
FUNCTION
RESET TO
FACTORY DEFAULTS
"CL"
ENTER
WHILE "CL" I S DI S PLAYED, P R E SS ENTE R
ALL P R O GR AMMED DATA WILL B E CLEA R ED
AND THE FACTO R Y DEFAULT S WILL B E
S TO R ED IN MEMO R Y.
NOTE : THIS FUNCTION WILL NOT ERASE
TRANSMITTERS, CURRENT SENSE VALUES,
OR MOTOR TYPE.
FUNCTION
DC MOTO R ONLY WITH BR AKIN G
AC MOTO R ONLY
DC MOTO R WITH S OFT S TA R T/ S TOP
AC MOTO R P R IMA R Y WITH
DC MOTO R B ACKUP WITH BR AKIN G
OPTIONS
P R E SS UP O R
DOWN TO CYCLE
TH R OU G H OPTION S
P R E SS ENTE R TO
S ELECT AN OPTION
MOTOR TYPE
SELECTION
NOTE : S ELECTION
MU S T MATCH
MOTO R B OA R D !
"MO"
3 PHA S E AC MOTO R
AC MOTO R P R IMA R Y WITH
DC MOTO R B ACKUP WITH S OFT S TA R T/ S TOP