background image

1

dc2043bfa

DEMO MANUAL DC2043B

Description

LTC3305EFE

Lead Acid Battery Balancer 

Demonstration circuit 2043B is a lead-acid battery balancer 

featuring the 

LTC

®

3305

. The LTC3305 balances up to four 

lead-acid batteries connected in series and incorporates all 

voltage monitoring, gate drive and fault detection circuitry. 

The LTC3305 employs an auxiliary battery or an alternative 

storage means to transfer charge to or from each individual 

battery within the stack. There are two operating modes, 

TIMER mode and CONTINUOUS mode, selected by the 

MODE pin. In TIMER mode, once the balancing operation 

is complete, the LTC3305 goes to a low power state for 

a programmed time and then periodically rebalances the 

L

, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear 

Technology Corporation. All other trademarks are the property of their respective owners.

BoarD photo

batteries. In CONTINUOUS mode, the balancing operation 

continues even after the batteries are balanced to their 

programmed termination voltage.
The LTC3305EFE is available in a 7mm 

×

 7mm 38-lead 

TSSOP surface mount package with exposed pad. 

Design files for this circuit board are available at  

http://www.linear.com/demo/DC2043B

Figure 1. DC2043B Demo Board

Figure 2. Thermal Image of DC2043B

Summary of Contents for LTC3305EFE











Reviews: