LT3695 Series
4
3695fa
ELECTRICAL CHARACTERISTICS
The
l
denotes the specifi cations which apply over the full operating
temperature range, otherwise specifi cations are at T
A
= 25°C. V
IN
= 10V, V
RUN/SS
= 10V, unless otherwise noted. (Note 4)
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
Switch V
CESAT
I
SW
= 1A
350
mV
DA Pin Current to Stop OSC
1.25
1.6
1.95
A
Switch Leakage Current
V
SW
= 0V, V
IN
= 36V
0.01
1
μA
Boost Schottky Diode Voltage Drop
I
BSD
= 50mA
720
900
mV
Boost Schottky Diode Reverse Leakage
V
SW
= 10V, V
BD
= 0V
0.1
1
μA
Minimum Boost Voltage (Note 8)
l
1.7
2.3
V
BOOST Pin Current
I
SW
= 0.5A
10.5
17.5
mA
RUN/SS Pin Current
V
RUN/SS
= 2.5V
V
RUN/SS
= 10V
l
4.5
12
7.5
20
μA
μA
RUN/SS Input Voltage High
2.5
V
RUN/SS Input Voltage Low
0.2
V
PG Leakage Current
V
PG
= 5V
0.1
1
μA
PG Sink Current
V
PG
= 0.4V
l
100
1000
μA
PG Threshold as % of V
FB
(LT3695) or
V
OUT
(LT3695-3.3, LT3695-5)
Measured at FB
(LT3695) or OUT1,2
(LT3695-3.3, LT3695-5)
Pins (Pin Voltage Rising)
88
90
92
%
PG Threshold Hysteresis
LT3695
Measured at FB Pin
12
mV
LT3695-3.3 Measured at OUT1,2, Pins
50
mV
LT3695-5
Measured at OUT1,2, Pins
75
mV
SYNC Threshold Voltage
300
550
800
mV
SYNC Input Frequency
0.3
2.2
MHz
Note 1:
Stresses beyond those listed under absolute maximum ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect the device
reliability and lifetime.
Note 2:
Positive currents fl ow into pins, negative currents fl ow out of pins.
Minimum and maximum values refer to absolute values.
Note 3:
Absolute maximum voltage at V
IN
and RUN/SS pins is 60V for
nonrepetitive 1 second transients, and 36V for continuous operation.
Note 4:
The LT3695E regulators are guaranteed to meet performance
specifi cations from 0°C to 125°C junction temperature. Specifi cations
over the –40°C to 125°C operating junction temperature range are
assured by design, characterization and correlation with statistical process
controls. The LT3695I regulators are guaranteed over the full –40°C to
125°C operating junction temperature range. The LT3695H regulators are
guaranteed over the full –40°C to 150°C operating junction temperature
range.
Note 5:
These ICs include overtemperature protection that is intended
to protect the devices during momentary overload conditions. Junction
temperature will exceed the maximum operating junction temperature
when overtemperature protection is active. Continuous operation above
the specifi ed maximum operating junction temperature may impair device
reliability.
Note 6:
This is the voltage necessary to keep the internal bias circuitry in
regulation.
Note 7:
Current limit guaranteed by design and/or correlation to static test.
Slope compensation reduces current limit at higher duty cycles.
Note 8:
This is the minimum voltage across the boost capacitor needed to
guarantee full saturation of the switch.