background image

2

dc1477bfa

DEMO MANUAL DC1477B

Quick start proceDure

Demonstration circuit DC1477B is an easy way to evalu-

ate the performance of the LTM4609EV. Please refer to 

Figure 1 for proper measurement equipment setup and 

follow the procedure below: 
1. Place jumpers in the following positions for a typical 

30V

OUT

 application:

RUN

CLOCK

MODE

START

ON

PROG

CCM

SSO

2. With the power supply off, connect the input power 

supply, load and meters as shown in Figure 1. Preset 

the load to 0A and V

IN

 supply between 10V to 36V. 

3. Turn on the power at the input. The output voltage 

should be 30V ± 2%.

4.  Once the proper output voltage is established, adjust the 

load within the operating range and observe the output 

voltage regulation, ripple voltage, efficiency and other 

parameters. A cooling fan and heat sink are necessary 

for V

IN

 <10V and I

OUT 

= 3A.

5. To measure input and output ripple, please refer to 

Figure 2 for proper setup.

6. To adjust the switching frequency turn off the power 

supply and modify R6 and R7. Do not allow voltage at 

pin PLLFLTR to exceed 2.4V.

7. Inductor and R

SENSE

 should be modified to accom-

modate certain input and output condition. Refer to 

the data sheet for details.

8. The input filter formed by CIN2, L2 and L3, CIN3 and 

CIN4 is for the purpose of reducing the input voltage 

ripple. The magnetic beads L2 and L3 are not necessary, 

but they help to reduce the high frequency ringings on 

the input supply significantly. See Figure 5 for details.

9.  The optional components Rsnb1 and Csnb1, Rsnb2 and 

Csnb2 can be used to form RC snubber circuits on the 

switching nodes, which may help to reduce the output 

ripple. Refer to the data sheet for details.

Summary of Contents for DC1477B










Reviews: