background image

 

 

- 9 - 

_

2000_xp_nt4.0\Sl3114r.inf

, click 

Open

 then 

OK

5. Highlight 

Silicon Image Sil 3114 SATARaid Controller 

and click 

OK

6.If the 

Insert Disk

 dialog appears, click 

OK

 then 

Browse. 

7.Highlight 

Sl3114r.sys 

and

 

click 

Open

 then 

OK

 

Verification of the Proper Installation for Windows NT 4.0 

1. Double click 

My Computer/Control Panel/SCSI Adapters

2. Highlight 

Silicon Image Sil 3114 SATARaid Controller 

and click 

Properties

This device is working properly

 is displayed in the dialog box, the driver has been 

correctly installed. 

 

4.4. Windows 2000 Driver Installation

 

For New Windows 2000 Systems (Fresh Installation) 

1. Before installation, copy all the files under directory E:\SATA Raid_4Port\ Sil3114\ 

Win98_me _

2000_xp_nt4.0\driver\ *.* to a blank floppy disk.   

2. After the 

SATA RAID PCI Host Adapter and attached drives are configured, follow 

Microsoft procedures to install Windows accordingly. 

3. At the 

Windows Set-up 

screen, press 

F6 

to specify and add the driver. 

4. Insert the Driver diskette. Press 

S

, then press 

Enter

5. Select 

Silicon Image SiI 3114 SATARaid Controller for Windows NT 4.0 and 2000 

and press 

Enter

6. Press 

Enter 

to continue and follow on-screen instructions to complete installation. 

 

Add Windows 2000 Driver on Original Booting Device 

1. After the 

SATA RAID PCI Host Adapter and attached drives are configured, boot up 

Windows. 

2. At the 

Found New Hardware Wizard

, click 

Next

3. Select 

Search for a suitable driver for my device (recommended) 

and click 

Next

4. Insert the Driver CD in your CD-ROM/DVD drive, check 

Specify a location

, uncheck 

the other boxes, click 

Next,

 type in 

E:\

 (If your CD-ROM/DVD is 

E

:\). Click 

Browse

5. Points specify a location, example 

E

:\

SATA Raid_4Port\Sil3114\Win98_me

 

_

2000_xp_nt4.0\Sl3114r.inf, 

click 

Open

 then 

OK

6. Click 

Next

 if the 

Digital Signature Not Found 

message appears, click 

Yes

. (

Note 

If 

prompted for Windows 2000 CD-ROM, insert the CD and click 

OK

. Type in 

E:\I386

, click 

OK 

and 

Finish

. (assuming 

E: 

is your CD-ROM drive)) 

7. Click 

Finish

 

4.5. Windows XP Driver Installation

 

Summary of Contents for 70541












Reviews: