Lindy 38121 User Manual Download Page 5

User Manual 

 

English 

Installation 

 

The  Wireless  Extender  can  be  used  in  horizontal  or  vertical  mode,  depending  on  your 

requirement, however for optimum performance it is recommened to operate in vertical mode. 

To use the Extender in vertical mode simply slide the foot, on the bottom edge of each unit, until 

it creates a 90

0

 angle with the body of the unit. 

 

The Wireless Extender is capable of sending a video signal up to 30m in an open environment 

or  up  to  20m  indoors  though  walls  and  floors.  Actual  distances  will  depend  entirely  on  the 

construction  of  the  building  and  any  walls  or  floors  that  are  situated  between  the  Transmitter 

and Receiver units. 

 
Important!

 Before starting the installation, please ensure that all devices are powered off. 

 

The  following  steps  are  for  an  installation  using  HDMI  equipment,  if  you  are  using  DVI 

equipment you should substitute the HDMI cables for DVI to HDMI cables where required. 

 

1.  Place the Transmitter unit  near your HDMI media device 

2.  Connect the IR Extension Cable to the IR port (1) on the Transmitter unit 

3.  Place the other end of the IR Extension Cable near the IR port of your HDMI media device 

4.  Connect  your  HDMI  media  device  to  the  HDMI  In  port  (2)  of  the  Transmitter  unit,  using  a 

standard HDMI cable  (included) 

5.  Place the Receiver unit near you HDMI display/projector 

6.  Connect your HDMI display/projector to the HDMI Output port (1) of the Receiver unit 

7.  Connect the supplied power supply units to the DC IN ports of the Transmitter unit (3) and 

Receiver unit (2) 

 

Once  these  steps  have  been  completed  the  Extender  is  ready  to  use,  simply  power  on  all 

devices to begin operation. 

 

Operation 

 

Once all equipment is turned on the Extender will initiate a Wireless link, successful connection 

of the link will be shown by the blue Wireless Link LED on both the Transmitter and Receiver 

units.  This  may  take  a  short  while  depending  on  the  distance  between  the  units  and  other 

environmental factors. 

When  the  initial  Wireless  Link  has  been  established  the  Extender  will  then  establish  a  Video 

Link between the Transmitter and Receiver units, once this has been completed a second blue 

Summary of Contents for 38121





















Reviews: