Lincoln SP-100T Page 21 Operator'S Manual Download | Manualshive

Page: 21 / 35

background image

C-1

ACCESSORIES

C-1

OPTIONAL ACCESSORIES

1.

K549-1 .035" (0.9 mm) Innershield® Welding Kit

—

Includes a contact tip, a gasless nozzle and a

.035/.045" (.9/1.2 mm) cable liner to permit the
Magnum

™

100L gun and cable to use .035" (0.9

mm) diameter flux-cored electrode. The fitting on
the end of the liner is stenciled with the maximum
rated wire size (.045"/1.2 mm). Also included is a
10 lb. (4.5 kg.) spool of .035" (0.9 mm) Innershield
NR-211-MP.

See

“

Innershield (FCAW) Conversion

”

in this sec-

tion for installation instructions and MAINTE-
NANCE section for proper feeding component con-
figuration and installation.

2.

K664-2 Aluminum Feeding Kit

—

This kit

required for welding with .035 Aluminum wire. This
kit may also be used for feeding .035 stainless
wire. Included with this kit are a drive roll, liner and
contact tip.

It is important when changing

between welding with steel wire and aluminum
to exchange these components due to the
lubricant applied to steel wire. Failure to do so
may result in contaminated welds when weld-
ing aluminum.

3.

KP1884-1 Drive Roll – Optional

—

Knurled drive

roll for feeding .035 (0.9 mm) diameter flux-cored
electrode.

4.

K520 Utility Cart

—

Designed to transport the

Lincoln family of small welders. Has provisions for
mounting a single gas cylinder. Has front casters
and large rear wheels. Handle height is easily
adjustable. Bottom tray provided for tools and
accessories. Easy assembly required; takes less
than 15 minutes.

5

.

K586-1 Deluxe Adjustable Gas Regulator &
Hose Kit

Accommodates CO2 or mixed Gas Cylinders.

SP-100T

«
...
19
20
21
22
23
...
»

Summary of Contents for SP-100T




































Reviews:

No comments

Related manuals for SP-100T

Brand: EAW Pages: 2

Brand: EAW Pages: 2

Brand: EAW Pages: 2

Brand: TCL Pages: 16

RAY-DANZ TS9030

Brand: TCL Pages: 32

Brand: TCL Pages: 19

Brand: Raytec Pages: 11

Brand: Telwin Pages: 164

Brand: Assa Abloy Pages: 8

Brand: Audio Concepts Pages: 13

Smartvest FUSG35000A

Brand: Abus Pages: 4

ABIPLAS CUT 200 W/MT

Brand: Abicor Binzel Pages: 100

Brand: Air Liquide Pages: 66

Brand: Bear Pages: 21

HTVZD*1C series

Brand: Halsey Taylor Pages: 7

NVL Vista 05 Series

Brand: Braun Pages: 30

Brand: MAC TOOLS Pages: 40

Brand: Monacor Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands