background image

Models 85622, 85628, 85626, 85637 Non-Metallic-REV1007 

 Page 16

PILOt VaLVe SerVICINg 

To service the pilot valve first shut 

off  the  compressed  air  supply,  bleed 
the  pressure  from  the  pump,  and 
disconnect the air supply line from the 
pump.

SteP  #1:  See  pump  assembly 

drawing.

Using  a  7/16"  wrench  or  socket, 

remove the four capscrews (item 12). 
Remove the air inlet cap (item 8) and 
air inlet gasket (item 20). The pilot valve 
assembly (item 3) can now be removed 
for inspection and service.

SteP #2: Disassembly of the pilot 

valve.

Remove the pilot valve spool (item 

3-D). Wipe clean and inspect  spool and 
o-rings for dirt, cuts or wear. Replace 
the o-rings and spool if necessary.

Remove  the  retaining  ring  (item 

3-F) from the end of the sleeve (item 
3-b)  and  remove  the  sleeve  from  the 
valve body (item 3-A). Wipe clean and 
inspect sleeve and o-rings for dirt, cuts 
or wear. Replace the o-rings and sleeve 
if necessary.

SteP #3: Re-assembly of the pilot 

valve.

Generously  lubricate  outside 

diameter  of  the  sleeve  and  o-rings. 
Then carefully insert sleeve into valve 
body. Take  CAUTION  when  inserting 
sleeve, not to shear any o-rings. Install 
retaining  ring  to  sleeve.  Generously 
lubricate outside diameter of spool and 
o-rings. Then carefully insert spool into 
sleeve. Take CAUTION when inserting 
spool,  not  to  shear  any  o-rings.  Use 
BP-LS-EP-2  multipurpose  grease,  or 
equivalent. 

SteP #4: Re-install the pilot valve 

assembly into the intermediate.

Be careful to align the ends of the 

pilot  valve  stem  between  the  plunger 
pins when inserting the pilot valve into 
the cavity of the intermediate.

Re-install  the  gasket,  air  inlet  cap 

and capscrews. Connect the air supply 
to the pump. The pump is now ready 
for operation.

Pilot Valve Servicing, assembly Drawing & Parts List

PILOt VaLVe aSSeMbLy PartS LISt

IteM 

Part NUMber 

DeSCrIPtION 

Qty

252897 

Pilot Valve assembly 

1

3-A 

252933 

Pilot Valve Body 

3-B 

274585 

Pilot Valve Sleeve with O-rings 

1

3-C 

275751 

O-ring 

6

3-D 

274587 

Pilot Valve Spool with O-rings 

1

3-E 

275752 

O-ring 

3

3-F 

274589 

Retaining Ring 

1

To order call 1-800-548-1191 or visit www.partdeal.com - [email protected]

Summary of Contents for 85622

























Reviews: