manualshive.com logo in svg

Lincoln 2006 Zephyr, Owner'S Manual

The Lincoln 2006 Zephyr Quick Reference Manual is a detailed user guide providing essential information on operating and maintaining your vehicle. This comprehensive manual can be easily downloaded for free from our website, offering you a convenient resource to ensure a seamless and enjoyable driving experience.

Share
Download
background image

TRACTION CONTROL

姟

The Traction Control

娂

system helps you maintain the stability and

steerability of your vehicle, especially on slippery road surfaces such as
snow- or ice-covered roads and gravel roads. The system will allow your
vehicle to make better use of available traction in these conditions.

During Traction Control

娂

operation,

the traction control active light will
illuminate, you may hear an electric
motor type of sound coming from
the engine compartment, and the
engine may not “rev-up” when you
push further on the accelerator. This is normal system behavior and
should be no reason for concern.

Aggressive driving in any road conditions can cause you to lose
control of your vehicle increasing the risk of severe personal

injury or property damage. The occurrence of a Traction Control

娂

event is an indication that at least some of the tires have exceeded
their ability to grip the road; this may lead to an increased risk of loss
of vehicle control, vehicle rollover, personal injury and death. If you
experience a severe road event, SLOW DOWN.

The Traction Control

娂

switch is

located on the instrument panel.
The Traction Control

娂

system will

automatically turn on every time the
ignition is turned off and on. The
Traction Control

娂

system should

normally be left on.

If you should become stuck in snow
or ice or on a very slippery road surface, try switching the Traction
Control

娂

system off by pressing the switch on the instrument panel.

Switching the Traction Control

娂

system off may allow excess wheel spin

to “dig” the vehicle out and enable a successful “rocking” maneuver.
When the Traction Control

娂

system is off, an indicator light will

illuminate and will remain on until the system is turned back on or the
ignition is turned off and on.

If a system fault is detected, the traction control active light will
illuminate, the Traction Control

娂

button will not turn the system on or

off and your vehicle should be serviced by an authorized dealer.

2006 Zephyr

(378)

Owners Guide (post-2002-fmt)
USA

(fus)

Driving

170

Summary of Contents for 2006 Zephyr


































































































































































































































































Reviews:

No comments

Related manuals for 2006 Zephyr

B-Speech B-Speech Prim Manual preview
B-Speech Prim
Brand: B-Speech Pages: 18
PUTCO MOLLE PANELS RAM 2500 Instruction Manual preview
MOLLE PANELS RAM 2500
Brand: PUTCO Pages: 4
Westfalia Portilo 350000 Installation And Operating Instructions Manual preview
Portilo 350000
Brand: Westfalia Pages: 18
Haibang HA998 Series Installation Instructions Manual preview
HA998 Series
Brand: Haibang Pages: 6
Honda 2011 Civic Sedan Vehicle Instruction Card preview
2011 Civic Sedan
Brand: Honda Pages: 5
Suzuki 990E0-54P56-000 Installers And Users Instructions preview
990E0-54P56-000
Brand: Suzuki Pages: 12
BMW E46/2 Coupe Manual preview
E46/2 Coupe
Brand: BMW Pages: 55
Whispbar K496W Fitting Instructions Manual preview
K496W
Brand: Whispbar Pages: 15
Oldsmobile 2004 Alero Quick Manual preview
2004 Alero
Brand: Oldsmobile Pages: 2
Ford 2004 Freestar Workshop Manual preview
2004 Freestar
Brand: Ford Pages: 8
Intec CVD500LCD Installation And Operation Manual preview
CVD500LCD
Brand: Intec Pages: 16
SAN HIMA SGBR015 Installation Instructions Manual preview
SGBR015
Brand: SAN HIMA Pages: 10
ULTIMATE SPEED 285690 Assembly And Safety Advice preview
285690
Brand: ULTIMATE SPEED Pages: 10
Safe Fleet PRIME DESIGN VCR-TC11B Assembly Instructions Manual preview
PRIME DESIGN VCR-TC11B
Brand: Safe Fleet Pages: 12
Xingyun XY40EV Service Manual preview
XY40EV
Brand: Xingyun Pages: 74
Saab 2000 9-5 2.3 Turbo Ecopower Owner'S Manual preview
2000 9-5 2.3 Turbo Ecopower
Brand: Saab Pages: 256
Chrysler Dodge Caravan 2002 Manual preview
Dodge Caravan 2002
Brand: Chrysler Pages: 2399
Ednet 84104 User Manual preview
84104
Brand: Ednet Pages: 6

Brands by name

Popular brands

Load more brands