manualshive.com logo in svg

Lincoln Electric RANGER GXT, Operator'S Manual

Share
Download
Lincoln Electric RANGER GXT Operator'S Manual Download Page 21

B-5

OPERATION

B-5

RANGER GXT

SUMMARY OF WELDING PROCESSES

CONTROL                               ELECTRODE

CABLE                IDLE           WHEN NOT                    TO  START

PROCESS                  USED                MODE           WELDING                        WELDING

STICK

No

AUTO

Hot

Touch electrode to work.
Welding starts immediately
and engine goes to high
idle.

WIRE FEED, LN-25 WITH

No

AUTO

Cold

Press gun trigger, LN-25

INTERNAL CONTACTOR

contactor closes. Welding
starts immediately and
engine goes to high idle.
NOTE:  Output Control 
must be set above 

“

3

”

TIG, TIG MODULE WITH

Yes

High

Cold

Press Amptrol,

WITH CONTACTOR KIT

contactor closes,

CONTROL CABLE, & 

welding starts immediately.

AMPTROL

WIRE FEED, LN-15

No

High

Cold

Press gun trigger.

ACROSS the ARC

LN-15 contactor closes,

(has internal contactor)

Welding starts immediately

Note

: Output Control must 

be set above 

“

3

”

.

Summary of Contents for RANGER GXT





































Reviews:

No comments

Brands by name

Popular brands

Load more brands