background image

A-4

INSTALLATION   

LN™-25 PIPE

A-4

WIRE DRIVE CONFIGURATION

(See Figure A.2)

CHANGING  THE  GUN  RECEIVER
bUSHING

ELECTRIC SHOCK can kill.

• Turn  the  input  power  OFF  at  the

welding  power  source  before  instal-
lation  or  changing  drive  rolls  and/or
guides.

• Do not touch electrically live parts.
• When  inching  with  the  gun  trigger,  electrode

and  drive  mechanism  are  "hot"  to  work  and
ground and could remain energized several sec-
onds after the gun trigger is released.

• Do  not  operate  with  covers,  panels  or  guards

removed or open.

• Only qualified personnel should perform mainte-

nance work.

------------------------------------------------------------------------

Tools required:    

• 1/4"  hex key wrench.
Note: Some gun bushings do not require the use of

the thumb screw.

1. Turn power off at the welding power source.
2. Remove the welding wire from the wire drive.
3. Remove the thumb screw from the wire drive.
4. Remove the welding gun from the wire drive.

5. Loosen  the  socket  head  cap  screw  that  holds  the

connector bar against the gun bushing.

Important:  Do  not  attempt  to  completely
remove the socket head cap screw.

6. Remove  the  outer  wire  guide,  and  push  the  gun

bushing out of the wire drive.  Because of the pre-
cision  fit,  light  tapping  may  be  required  to  remove
the gun bushing.

7. Disconnect  the  shielding  gas  hose  from  the  gun

bushing, if required.

8. Connect  the  shielding  gas  hose  to  the  new  gun

bushing, if required.

9. Rotate the gun bushing until the thumb screw hole

aligns with the thumb screw hole in the feed plate.
Slide  the  gun  receiver  bushing  into  the  wire  drive
and verify the thumb screw holes are aligned.

10. Tighten the socket head cap screw.
11. Insert  the  welding  gun  into  the  gun  bushing  and

tighten the thumb screw.

GUN RECEIVER BUSHING

LOOSEN       TIGHTEN

THUMB SCREW

OUTER WIRE GUIDE

SOCKET HEAD
CAP SCREW

CONNECTOR BLOCK

GUN RECEIVER BUSHING

LOOSEN       TIGHTEN

THUMB SCREW

OUTER WIRE GUIDE

SOCKET HEAD
CAP SCREW

CONNECTOR BLOCK

WARNING

PROCEDURE  TO  INSTALL  DRIVE  ROLLS
AND WIRE GUIDES

• Turn  the  input  power  OFF  at  the

welding  power  source  before  instal-
lation  or  changing  drive  rolls  and/or
guides.

• Do not touch electrically live parts.
• When  inching  with  the  gun  trigger,  electrode

and  drive  mechanism  are  "hot"  to  work  and
ground and could remain energized several sec-
onds after the gun trigger is released.

• Do  not  operate  with  covers,  panels  or  guards

removed or open.

• Only qualified personnel should perform mainte-

nance work.

------------------------------------------------------------------------

1. Turn power off at the welding power source.
2. Release the idle roll pressure arm.
3. Remove the outer wire guide by turning the knurled

thumbscrews  counter-clockwise  to  unscrew  them
from the feed plate.

4. Rotate  the  triangular  lock  and  remove  the  drive

rolls.

5. Remove the inner wire guide.
6. Insert  the  new  inner  wire  guide,  groove  side  out,

over the two locating pins in the feed plate.

7. Install  a  drive  roll  on  each  hub  assembly  secure

with the triangular lock.

8. Install  the  outer  wire  guide  by  aligning  it  with  the

pins and tightening the knurled thumbscrews.

9. Close the idle arm and engage the idle roll pressure

arm.  Adjust the pressure appropriately.

WARNING

FIGURE A.2

Summary of Contents for LN- 25 PIPE IM10056








































Reviews: