manualshive.com logo in svg

Lincoln Electric Demo Zone K1854-2, Operator'S Manual

Share
Download
Lincoln Electric Demo Zone K1854-2 Operator'S Manual Download Page 8

A-1

INSTALLATION   

DEMO ZONE

A-1

TECHNICAL SPECIFICATIONS - Demo Zone (K-1854-2)

Voltage Specification

Input Connection 

Specification

230 VAC single phase, 40 amps 

Type 6-50P plug 

ELECTRICAL INPUT REQUIREMENTS

RATED OUTPUT

HEIGHT WIDTH

DEPTH

WEIGHT

86.00 in.(With Sign)

68.00 in.

54.00 in.

2150 lbs. (w/o gas cylinders)

65.00 in. (With out Sign)

2910 lbs. (with gas cylinders)

2184.4 mm (With Sign)

1727.2 mm

1371.6 mm

975.2 kg. (w/o gas cylinders)

1651.1 mm (With out Sign)

1319.9 kg. (with gas cylinders)

The Demo Zone is intended for display and demonstration use.  It is intended for light duty operation.
The Demo Zone operator must observe the 40 amp input current limitation. Because of the input power
limitation, power sources (except Ranger 250 and ZR-10) when used at maximum output must be oper-
ated at low duty cycles. Refer to Welder Operation - Duty Cycle section of this manual.

PHYSICAL DIMENSIONS

Summary of Contents for Demo Zone K1854-2























Reviews:

No comments

Brands by name

Popular brands

Load more brands