background image

English 5 English 

Introduction 

 

COOL ARC

® 

26

 cooler is a stand alone recirculating 

cooling system designed to use with MIG welding power 
sources that lists the 

COOL ARC

® 

26

 as an approved 

accessory. 
 
The following equipment is included with the 

COOL ARC

® 

26

  Hose with quick water connector: 

 Blue (115 

mm), Red (150 

mm) hose for 

connection to a welding source. 

  Black hose that will be used in filing procedure 

(200 mm) 

  M5x20 screw for fixing to the power source by 

spanner size 8. 

 

The 

COOL ARC

® 

26

 is delivered empty with no coolant 

in the system. FREEZCOOL - W000010167 is 
recommended. 
 
 
 
 
 
 
 
 
 
 
 
 
 

Unpacking 

 

Unpacking the COOL ARC

® 

26 

The packaging of the Cooler is designed to withstand 
shipping abuse, and contains a cardboard liner that 
surrounds the unit. If any shipping damages have been 
occurred, contact your certified Lincoln distributor or 
service center. 
 

When unpacking the unit, avoid thrusting sharp objects 
through the carton liner, which may puncture the plastic 
reservoir. Save the manual instruction and service 
directory supplied with the 

COOL ARC

® 

26

 for parts 

orders and future maintenance service. 
 
 
 

Installation on Power Source 

 
The 

COOL ARC

®

 26

 need to be mounted directly to the 

chassis of MIG welding power source that lists the 

COOL ARC

®

 26

 as an approved accessory. 

 

 WARNING

 

Only a qualified electrician can connect the welding 
machine to the supply. Installation had to be made in 
accordance with the appropriate National Electrical Code 
and local regulations. 
 

 WARNING

 

Before connecting 

COOL ARC

® 

26

 turn off the power 

source and disconnect it from the input supply. 
 
 

INSTALATION: 

  Unscrew the side panel (Figure1) 

  Remove the side panel (Figure 2) 

  Unscrew and remove the cover bracket (Figure 3) 

  Place cooler in the base positioning pins (Figure 4) 

  Screw the cable holder bracket (Figure 5) 

  Connect the 10-pin plug to receptacle and screw 

protective earth green/yellow wire terminal 
(Figure 6). 

  Screw side panel (Figure 7) 

  Screw side panel. (Figure 8) 

  Final assembly (Figure 9) 

 
 
 
 

Summary of Contents for Cool Arc 26






















Reviews: