Maintenance Instruction
10.3
Bearb.: Stolinski
Replaces edition from: 13.09.96
Gepr. + Freig.:
Edition: 18.12.02
Page: 2 of 2 Pages
Reg.-Nr.: 041 Datei:
MI10-3.DOC
Part
Engine Model
Float chamber
Jet needle valve
Number
needle valve
Type
Adjustment
170.130.001 L 1700 E0
1,75
6A
+2,0
170.130.002 L 1700 EA
1,75
6A
0
170.130.005 L 1700 EC
1,75
6A
+2,0
170.130.010 L 1700 EB left
1,75
6A
0
170.130.011 L 1700 EB right
1,75
6A
0
201.130.001 L 2000 E0, only RF5
1,75
6A
0
201.130.002 L 2000 E0, EA, EC
1,75
6A
0
205.130.002 L 2000 DA
1,75
6A
0
201.130.011 L 2000 E0, only RF5
1,75
B2BA
+1,5
201.130.010 L 2000 E0, EC
1,75
B2BA
+1,5
201.130.010 L 2000 EA
1,75
B2BA
+1,75
205.130.010 L 2000 DA
1,75
B2BA
+2,0
204.130.007 L 2000 EB1.AA left
1,75
B5CK
+2,0
204.130.008 L 2000 EB1.AA right
1,75
B5CK
+2,0
206.130.005 L 2000 EB left
1,75
B5CK
+2,0
206.130.006 L 2000 EB right
1,75
B5CK
+2,0
207.130.005 L 2000 EB1.AB, AC left
1,75
B5CK
+2,0
207.130.006 L 2000 EB1.AB, AC right
1,75
B5CK
+2,0
244.130.007 L 2400 EB1.AA left
1,75
B5CK
+2,0
244.130.008 L 2400 EB1.AA right
1,75
B5CK
+2,0
245.130.005 L 2400 EE2
1,75
B5CK
+2,0
246.130.005 L 2400 EB1.AD
1,75
B5CK
+2,0
247.130.005 L 2400 EB1.AB, AC left
1,75
B5CK
+2,0
247.130.006 L 2400 EB1.AB, AC right
1,75
B5CK
+2,0
Checking float and float level
1. Unscrew screws (36) and remove float chamber (35) with gasket (34).
2. Pull off float (33) with float axle (32) from support.
3. Check float for leaks. Dip float totally into water of about 90 °C and check if air bubbles come up from
the float body. If this is the case the float has to be discarded.
4. Lock float with float axle into the support - the sparings of the float point to the carburetor housing.
5. Check float level. Turn carburetor with float to top and check level with gauge p/n: 803.001.005 above
raised and flat face of carburetor housing. Put the template onto the raised and flat face - both
chambers of the float lightly touch the lower edge of the template at its highest elevation, the weld
seam of the chambers is parallel to the raised and flat face. Correct float gage by bending the lever for
the float needle valve.
6. Mount float chamber with new gasket, coat center screws lightly with sealant (CURIL-T), tighten
screws.
Replacing float needle valve
1. Unscrew screws (36) and remove float chamber (35) with gasket (34).
2. Pull off float (33) with float axle (32) from the support.
3. Unscrew float needle valve.
4. Mount new float needle valve with new conical nipple.
5. Lock float with float axle into the support - the sparings of the float point to the carburetor housing.
6. Check float level.
7. Mount float chamber with new gasket, coat center screws lightly with sealant (CURIL-T), tighten
screws.
