Lika MTA1 User Manual Download | Manualshive

Page: 27 / 48

background image

SMA1

Preset / Offset

register and activate it by sending the command

activate Preset / Offset

(set “02” in the register 48).

Default =

05h

.

Preset / Offset

[51 … 53, rw]

This function is available only if the

Enable preset / offset

parameter in the

Configuration

register is set to ENABLE. Furthermore it has a double function

depending on whether the

Set preset / offset

parameter in the

Configuration

register is set to PRESET or OFFSET. In the first case (

Set preset / offset

=

PRESET) the

Preset / Offset

register is used to set the preset value; while in the

second case (

Set preset / offset

= OFFSET) the

Preset / Offset

register is used

to set the offset value.

WARNING

Activate the preset / offset value only when the device is not moving.

Preset

The preset function is meant to assign a value to a desired physical position of
the sensor. The chosen physical position will get the value set next to this item
and all the previous and following positions will get a value according to it. This
function is useful, for example, when the zero position of the sensor and the
zero position of the axis need to match. The preset value will be set for the
position of the sensor in the moment when the preset value is activated. To
activate the preset, stop the sensor in the desired position, enter the desired
value next to this

Preset / Offset

register and then send the

Save and activate

Preset / Offset

command in the

register (set “02” in the register 48).

Offset

The offset function is meant to assign a value to a desired physical position of
the sensor so that the output position information is shifted according to the
value set next to this

Preset / Offset

register. The number of transmitted values

will match the maximum number of position information as per the set
resolution, but the output information will range between the

Preset / Offset

value (minimum value) and the sum of the max. position information as per the
set resolution (see the

Absolute resolution

register) + the

Preset / Offset

value (maximum value). The offset value will be set for the position of the
sensor in the moment when the offset value is activated. To activate the offset,
stop the sensor in the desired position, enter the desired value next to this

Preset / Offset

register and then send the

Save and activate Preset / Offset

command in the

register (set “02” in the register 48).

MAN SMA1 E 2.9.odt

6 - BiSS B-mode interface

27 of 48

«
...
25
26
27
28
29
...
»

Summary of Contents for MTA1

















































Reviews:

No comments

Related manuals for MTA1

Brand: ICP DAS USA Pages: 85

Brand: ICP DAS USA Pages: 6

Brand: ICP DAS USA Pages: 107

Brand: ICP DAS USA Pages: 8

Brand: ICP DAS USA Pages: 12

Brand: Planet Pages: 7

Music Maker 2396

Brand: Califone Pages: 1

Brand: StarTech.com Pages: 3

Brand: Icy Box Pages: 30

Brand: Millennia Pages: 2

Brand: Nuova Marea Pages: 9

Brand: Tyba Pages: 14

Media Giant CM3G Series

Brand: Conceptronic Pages: 2

Brand: Lambda Pages: 47

Brand: Kramer Pages: 17

Brand: Elabs Pages: 10

Brand: DROPSA Pages: 8

Brand: Raider Pages: 108

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands