Lightware RAP-B511-EU-K User Manual Download Page 13

Page: 13 / 73

2. Installation

RAP-B511 series

– User's Manual

2.2.

Powering Options

RAP-B511 series automation panel is compatible with IEEE 802.3af standard - Power over Ethernet (PoE) -

and one Ethernet port can receive, and the other one can send power over the Ethernet line.
The room automation panel can be powered by any of the following ways:

Local adaptor and remote power (PoE OUT)

When it is locally supplied with 48V DC adaptor, the room automation panel is able to send remote power via

POE OUT RJ45 connector to other PoE-compatible device.

Remote power injector (PoE IN)

The RAP-B511 can be powered remotely by a PoE-compatible power injector, like a PoE-compatible switch.

Connect it to the POE IN labeled RJ45 connector.

Standalone Matrix or Matrix board (PoE IN)

Powering by a matrix board* over the CATx (TPS) cable. Output board needs to be powered by an external

PSU. Connect it to the POE IN labeled RJ45 connector.
* TPS2 I/O board with PoE extension (-P)

INFO: Over the CATx cable, the Ethernet communication is transmitted.

Local adaptor and

remote power (PoE out)

Remote power injector (PoE in)

Matrix board (PoE in)

48V DC
Power
adaptor

MX-T

PS2-IB-P

DC IN

8 CH T

PS INPUT

BOARD WITH POE

48V 5

Eth

ern

S IN

TPS I

N 2

TPS

TPS I

N 4

8CH INPUT

ARD

FOR H

DMI

WITH 3D

AND

ANAL

AUDIO

MX-HD

MI-3D

-IB-A

IN 1

IN 2

IN 3

IN 4

MX-T

PS2-OB-S

48V 5A

DC IN

8 CH T

PS OUTP

UT BO

ARD W

ITH DIGIT

AUD

12V p

ower o

n TPS co

nnect

or. Only use wit

h compatible devices!

12V p

ower o

n TPS co

nnect

or. Only use wit

h compatible devices!

TPS O

UT 2

TPS O

UT 3

TPS

OUT 4

8CH OUTP

UT BOA

RD FO

R HD

MI WIT

H 3

D AND

ANA

LOG

AUD

MX-HD

MI-3D

-OB

-A OUT 1

OUT 2

OUT 3

OUT 4

CATx
(TPS)

External
power supply

Power send

Power

send

RAP-B511-EU-K

PoE-compatible unit

RAP-B511-EU-K

Power send

RAP-B511-EU-K

PoE-compatible switch

2.3.

Connecting Steps

Power adaptor

GPIO

Power

RS-232

Smartphone

Relay box

Projector

LAN

Lightware device

Ethernet switch

OFF

AUTO

GPIO

Connect a controller/controlled device (e.g. relay box) to the GPIO port.

RS-232

For RS-232 extension: connect a controller/controlled device (e.g. Projector) to the RS-232 port.

LAN

▪

Connect the switcher to a LAN network in order to control the device.

▪

Connect a PoE-compatible device for remote powering and control to the PoE out LAN port.

Built-in infra detector is ready to receive any IR signal without user intervention.

Power

Powering on the devices is recommended to do as the final step during the installation. Please check the

Powering Options

section for the details.









Summary of Contents for RAP-B511-EU-K










































































Search results

Summary of Contents for RAP-B511-EU-K

Reviews:

Lightware RAP-B511-EU-K, User Manual, Page: 13 / 73

Search results

Summary of Contents for RAP-B511-EU-K

Reviews: