Lightolier is a Philips group brand
631 Airport Road, Fall River, MA 02720 • (508) 679-8131 • Fax (508) 674-4710
We reserve the right to change details of design, materials and finish.
www.lightolier.com © 2008 Philips Group • A0908
Architectural Decorative
IS:CCLPS602P
Page 1 of 4
Instruction Sheet for Assembly and Installation
Read and understand these instructions before installing luminaire
This luminaire is intended for installation in accordance with the National Electrical Code and local regulations. To assure full compliance with local codes and
regulations, check with your local electrical inspector before installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
Getting Started
CCLPS602P is a compact power/data supply for indoor installations. CCLPS602P
provides power and data to Lightolier concealed color lighting product lines, and
is available for DMX and Ethernet control options.
The “s” type of power supply provides additional features, such as base address
and grouping of luminaire addresses, without the need for external components.
This instruction guide contains important information on installing and using your
new CCLPS602P. Please read it carefully and save it for future reference.
Included In This Box
• Power/data supply
• US Grounded IEC Power Cord Set
• RJ-45 Terminator
• Instruction Sheet
Additional Items Needed
• Mounting hardware – 4 flat head screws M3.5 or #6
Scope of this Instruction Guide
The goal of this user guide is to explain the steps necessary to install
CCLPS602P for DMX and Ethernet control to assure peak performance. Its
intended use is for reference only, by persons who are fully qualified. This docu-
ment should never be considered a substitute for any provisions of a regulation
or state and/or local code.
Identification and Warnings of Safety Hazards
In accordance with ANSI Z535.4-2002, the following system identifies the sever-
ity of the hazards associated with the products:
“Danger”
Imminently hazardous situation which, if not avoided, will result in
death or serious injury.
“Warning”
Potentially hazardous situation which, if not avoided, could result in
death or serious injury.
“Caution”
Potentially hazardous situation which, if not avoided, may result
in minor or moderate injury or property damage. Also used to alert
against unsafe practices.
Ignoring a hazard will void any warranty.
Warning:
Ensure that power is disconnected before installing, wiring, or servic-
ing the CCLPS602P power supply.
Warning:
The CCLPS602P power supply must be installed by a qualified profes-
sional in accordance with NEC and relevant local codes.
Warning:
Do not attempt to install or use CCLPS602P until you read and under-
stand the installation instructions and safety labels.
Warning:
Do not use CCLPS602P if power cables are damaged.
Warning:
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference
to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required to
take adequate measures.
Caution:
Ensure that CCLPS602P is securely attached, properly mounted, and
free of excessive vibration.
Caution:
Do not hot swap. Ensure the power supply is off before connecting or
disconnecting luminaires.
Caution:
Do not modify or alter CCLPS602P.
Note:
The instructions and precautions set forth in this installation guide are
not necessarily all-inclusive or relevant to all applications as Lightolier cannot
anticipate all conceivable or unique situations.
Owner/User Responsibilities:
It is the responsibility of the contractor, installer, purchaser, owner, and user to
install, maintain, and operate CCLPS602P in such a manner as to comply with
all state and local laws, ordinances, regulations, and the American National
Standards Institute Safety Code.
Note:
CCLPS602P is shipped with a US IEC power cord. For international cus-
tomers, use a country-specific IEC cable meeting the following specifications:
3-conductor, 18AWG (1.00mm2), HAR rating for Europe, and JET rating for Japan.
(Hard Service Type ST or equivalent.)
Note:
Ensure the IEC inlet plug fits in the supplied lock. The lock may not accom-
modate all plug styles.
Installation:
CCLPS602P must be installed by a qualified electrician in accordance with NEC
and relevant local codes for power supplies. A power screwdriver is recom-
mended for mounting the unit.
Mounting the Housing
• Select the location to mount the housing, keeping CCLPS602P within the
maximum distance specified for your luminaire. Refer to your luminaire user
guide for the cable run information.
Caution:
CCLPS602P must be installed in a location that allows air to move
freely. Packing insulation around the housing or mounting in a sealed location
that raises ambient temperature above 122°F (50°C) may result in property dam-
age and may void the warranty.
Note:
Ensure that there is adequate space to make all connections to the front
and rear of the unit.
• Mount the housing to a flat surface using four M3.5 or #6 flat head screws
suitable for the mounting surface. Mounting slots are located on each end of
the housing. (See Fig. 1.)
Note:
Do not overtighten the mounting screws.
(21.2 cm)
8.31"
(5.7 cm)
2.25"
Fig. 1
