Instruction Sheet Number
IS:8031
Page 2 of 2
Installation of Calculite
®
Compact Fluorescent Downlights and Wall Washer Reflector Trims
Lightolier
a Genlyte company
www.lightolier.com
631 Airport Road, Fall River, MA 02720 • (508) 679-8131 • Fax (508) 674-4710
We reserve the right to change details of design, materials and finish.
© 2006 Genlyte Group LLC • B0306
W
al
l t
o
be
Il
lu
m
in
at
ed
Lens Wall Washer
Junction Box
(positioned away
from wall)
Open Wall Washer
FIG. 9A
W
al
l t
o
be
Il
lu
m
in
at
ed
Junction Box
(positioned away
from wall)
Retaining Spring
Removed
FIG. 10A
FIG. 10
Junction
Box
Mounting
Frame
Fig. 9
Fig. 9A
Lensed Wall Washer
Junction Box
(Positioned Away
From Wall)
Open Wall Washer
Fig. 10
Fig. 10A
Mounting
Frame
Junction
Box
Retaining Spring
Removed
Junction Box
(Positioned Away
From Wall)
Junction Box
(positioned away
from wall)
Lens Trim
w/ Torsiontite
Spring
W
al
l t
o
be
Il
lu
m
in
at
ed
Leave approx.
1" exposed
Socket Cup
Slot
Reflector
Fig. 11
Junction Box
(Positioned Away
From Wall)
FIG. 12
Fig. 12
INSTALLATION OF LENS WALL WASHER AND OPEN
WALL WASHER
Note: Before installing Reflector, make sure the Mounting Frame is
installed with the Junction Box away from the wall to be illuminated
(FIG. 9 & 9A).
FOR OPEN WALL WASHER
(6132 Series Only)
1. Remove two
Retaining Springs
that are near the
Junction Box
from the
Mounting Frame
(FIG 10).
2. Insert two new
Retaining Springs
(that are provided with the
reflector trim) into pockets on the Mounting Frame (FIG. 10A).
3. Squeeze
Retaining Spring
into position with pliers (FIG. 10A)
FOR OPEN WALL WASHER
(N/S 6132 Series)
1. By hand, bend the 2 retaining springs that are near the junction box
as far back as possible pushing toward J Box.
A. INSTALL WHITE TRIM RING
(FIG. 1, 2, 3 & 4)
NOTE: Omit this section if reflector is self-flanged.
1. For overlapping trim installation (FIG. 1) slip
White Trim Ring
over
Reflector
, as shown in Fig 2 & 3.
2. For flangless trim installation (FIG. 4),
White Trim Ring
is
not required.
B. SNAP-IN
(FIG. 5)
Engage Retaining Spring into Slots in Reflector (see FIG. 5) following
chart below. See Frame-in kit for lamp information.
C. PUSH-UP REFLECTOR
(N/S 6132 Series)
1. Tilt
Reflector
so only (1)
Retaining Spring
(retaining spring closest to
junction box) touches the
Kick Reflector
. Push reflector up to clear larger
portion of Kick Reflector past the retaining springs and twist into positon.
LENS WALL WASHER
1. Tilt
Reflector
and insert
Socket Cup
into ceiling opening on side
opposite
Junction Box
. Push
Reflector
up leaving approximately one
inch of the
Reflector
exposed below the
Ceiling Line
(FIG. 11).
2. Compress
Torsiontite Springs
on
Lens Trim
by squeezing with
fingers. Insert into
Slots
in
Reflector
and push up until flush with
ceiling (FIG. 11).
NOTE: To remove
Reflector
, lift
Lens
and pull
Lens Trim
down
(FIG. 12). Disengage the
Socket Cup
by depressing the
Retaining
Spring
(FIG. 5). Turn
Reflector
counterclockwise while pulling
downward. After starting, use both hands to remove (FIG. 7)
OPEN WALL WASHER
1. Tilt
Reflector
and insert
Socket Cup
into ceiling opening on side
opposite
Junction Box
. Pivot
Reflector
and push it up into ceiling
(FIG 6).
NOTE: To remove
Reflector
, disengage the
Socket Cup
by depressing
the
Retaining Spring
(FIG. 5). Turn
Reflector
counterclockwise while
pulling downward. After starting, use both hands to remove, see FIG 7.
D. LAMPING
(FIG. 8)
NOTE: See
Socket Cup
Label for lamping information.
Line up
Lamp Pins
with
Socket
, tilt lamp base to engage, then bring
Lamp to horizontal position and push into
Socket
(FIG. 8). To relamp,
CAREFULLY PULL STRAIGHT OUT OF SOCKET WITH ONE FINGER
PLACED ON THE TOP OF THE LAMP.
CARE AND MAINTENANCE OF ALZAK REFLECTOR
See page. 1
