LIGHT MY BRICKS LEGO Land Rover Defender 42110 Manual Download Page 29 | Manualshive

Page: 29 / 69

background image

Note: If you experience any issues with the lights not working and suspect an issue with a

component, please try a different port on the expansion board to verify where the fault lies
(with the light, expansion board or effects board). To correct any issues with expansion board
ports, please view the section addressing expansion board issues on our

online troubleshooting

guide.

10.)

Take the following remaining head light sections and reassemble and connect them back

to the front of the vehicle. Reconnect all the sections we disconnected earlier surrounding the
left side.

«
...
27
28
29
30
31
...
»

Summary of Contents for LEGO Land Rover Defender 42110






































































Reviews:

No comments

Related manuals for LEGO Land Rover Defender 42110

Brand: Wagan Pages: 4

Brand: BARTEC FEAM Pages: 11

Solight URZ0019

Brand: VIPOW Pages: 2

LEDWP-500-M-20C

Brand: Larson Electronics Pages: 2

Brand: SATA Pages: 12

Brand: Tektronix Pages: 83

Brand: Cotech Pages: 5

Brand: PXM Pages: 19

Brand: Sealey Pages: 2

Brand: KSR Pages: 2

LIGHT SKY 1810 BEAM FX

Brand: Fly Dragon Pages: 28

PPA Int'l OLSMSRGB

Brand: OLS Pages: 2

ML-30 CDM Multi Lens Spot

Brand: EuroLite Pages: 37

Brand: Sagitter Pages: 36

Brand: Emerson Pages: 12

Brand: Emerson Pages: 4

Brand: Emerson Pages: 2

Brand: ArtFox Lightning Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands