LIGHT MY BRICKS 75244 Instructions Manual Download Page 52 | Manualshive

Page: 52 / 94

background image

Test the wireless power connection by taking the Cabin Roof and connecting it
directly on top of the cabin. Ensure the two wireless connectors connect with
each other. Turn the USB Power Bank ON and the lights on the cabin roof
should illuminate.

Troubleshooting: If the roof lights do not turn ON, check that the wireless power
connector cables are correctly connected into the expansion board ports.
Ensure both wireless connector positive and negative are in line with each
other and that the wireless power connector cables are facing the same way.

«
...
50
51
52
53
54
...
»

Summary of Contents for 75244































































































Reviews:

No comments

Related manuals for 75244

Brand: Ecco Pages: 3

Brand: Keithley Pages: 67

Brand: Keithley Pages: 23

Brand: Keithley Pages: 93

Brand: Oki Pages: 44

Brand: Magnescale Pages: 64

Brand: LANGER EMV-Technik Pages: 25

Electric Clamshell CSE12-208VCD

Brand: Lang Pages: 16

Brillion 3631-25

Brand: Landoll Pages: 138

Brand: TEC Pages: 6

Brand: U Technology Pages: 6

Brand: Eternal Flame Pages: 2

Pro hunter 2525

Brand: SprotDog Pages: 28

Brand: Barikell Pages: 32

Brand: Flex-A-Seal Pages: 7

Brand: Topcon Pages: 38

Brand: Stone Pages: 36

Brand: Scilogex Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands