LIGHT MY BRICKS 75181 Manual Download Page 12 | Manualshive

Page: 12 / 46

background image

6.)

Take the

Multi Effects Board

and connect both bit light cables from the cannons to the OUT

ports (side with 2 ports). Take the

AA Battery Pack

and insert 3x AA Batteries to it. Connect

the battery pack cable to the IN port (side with 1 port). Turn ON the battery pack to test the
cannon lights are working OK, then adjust the settings on the Multi Effects Board for the
“firing” effect. Set the switch to the middle setting and turn the speed wheel all the way to
the left for the slowest speed.

«
...
10
11
12
13
14
...
»

Summary of Contents for 75181















































Reviews:

No comments

Related manuals for 75181

Brand: Sunoptic Surgical Pages: 96

Brand: Parkside Pages: 39

Brand: STARVILLE Pages: 56

Brand: Mark Pages: 24

Brand: ADJ Pages: 14

LED Shoebox Fixture

Brand: Energetic Lighting Pages: 5

Brand: g-lites Pages: 18

Brand: GE Pages: 4

Brand: GE Pages: 2

Brand: GE Pages: 2

Brand: GE Pages: 2

Brand: Lightolier Pages: 1

Brand: Lightolier Pages: 2

Lytecel LCS6G20LW228

Brand: Lightolier Pages: 2

Lytecaster 2022

Brand: Lightolier Pages: 2

Lytecaster 2026WH

Brand: Lightolier Pages: 1

Lytecaster 2000AIC

Brand: Lightolier Pages: 1

Lytecaster 1101FEL

Brand: Lightolier Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands