18
19
Note
-
The alarm will sound for 2 minutes if you do not deactivate it by pressing any button. In this case the
alarm will be repeated automatically after 24 hours.
-
Rising alarm sound (crescendo, duration: 2 minutes) changes the volume 4 times whilst the alarm signal
is heard.
Switching off the alarm signal
Press any button except the “
” button to stop the alarm signal. It is not necessary to reactivate the
alarm. The alarm will set itself automatically to the previously set time.
Snooze function
Touch the “
“ field or press the “
” button to activate the snooze function. The alarm signal
will sound again after approx. 5 minutes.
Lunar phases
The weather station has a display which automatically displays the current lunar phase
°C/°F temperature display
-
The temperature is displayed either in °C or °F. Briefly press the “ ” button to switch between the
individual modes.
Comfort display
-
indoor comfort level is calculated according to the indoor temperature and humidity, a total of 5 levels.
Displaying temperature/humidity/barometric pressure and temperature/humidity trend
-
The current indoor temperature/humidity/barometric pressure and the temperature/humidity trend
(indoors) are shown in the LCD display.
-
After successfully connecting with the remote sensor, the weather station can display the remote tem-
perature/humidity and the temperature/humidity trend (remote)
-
You may see the following displays:
The temperature/humidity is rising.
The temperature/humidity is remaining constant.
The temperature/humidity is falling.
1.
1.
New moon
Waxing
half-moon
Half-moon
Waxing full
moon
Full
moon
Waning full
moon
Half-moon
Waning
half-moon
Comfortable Too cold or too hot
Remote sensor transmission
When the Weather Station successfully receives signals from the wireless sensor, the temperature and
humidity of the “REMOTE SENSOR” are displayed on the “REMOTE SENSOR” column of the weather
station. The weather station can connect with up to 3 channel wireless sensors, but you can only choose
one channel at a time.
Press the “ ” key to switch the display of different channels of remote temperature and humidity. When
the “ “ is displayed, the channel will automatically switch every 5 seconds to different channels.
If the weather station failed to receive transmission from a remote sensor (“- -”display on the LCD),
press and hold the “ ” button for 3 seconds to receive transmission manually. The remote temperature
will show an animation of the RF antenna symbol, the Base Station will re-receive the wireless signal of
the remote sensor.
Note
-
When the wireless sensor sets different channels, the weather station “REMOTE SENSOR” also wants
to switch to the same channel. When there is no wireless sensor signal transmission on the channel, “--”
will be displayed in the channel of the weather station
-
When the wireless remote sensor has no channel selection function, the sensor defaults to channel 1.
Maximum / Minimum Temperature/and Relative Humidity
To switch between indoor/remote maximum, minimum temperature and humidity data, press the
“MEM” button:
-
Once to display the maximum temperature and humidity values.
-
Twice to display the minimum temperature and humidity values
-
Three times to return to the current temperature and humidity levels
To reset the maximum and minimum temperature and humidity, press and hold down the “MEM”
button for about 2 seconds. This will reset all minimum and maximum data recorded to the current
displayed values.
Note
-
If the temperature reading is below the temperature range, tLL.L will be displayed. If the temperature
reading is above the temperature range, HH.H will be displayed.
Setting the Remote Temperature Alert
Press and hold down the “ ” button for 2 seconds until the “Temperature Alert” icon starts to flash
The icon of Upper limit of the Temperature alarm starts to flash. Use the “ ” and “ ” buttons to set
the required maximum temperature. Press “ ” to confirm your setting.
The icon of the Lower limit of the Temperature alarm starts to flash. Use the “ ” and “ ” buttons to set
the required minimum temperature. Press “ ” to confirm your setting and to end the setting procedure
Note:
-
Before entering the setup, you must select the correct channel, different channels can set different
temperature alarm ranges.
Temperature and frost alert
Press “ ” to activate or deactivate the remote temperature alert. When the remote temperature alarm
is activated, the temperature alarm icon is displayed in the remote sensor bar.
When the remote channel temperature value exceeds the set temperature range, the alarm will be acti-
vated. The Weather Station alarm will sound 5 times continuously every minute, while the temperature
alarm “ “ flashes. If the temperature activates the alarm, the upper limit icon “ “ or the lower limit
icon “ “ also flashes.
When the temperature of REMOTE SENSOR is –1°C to + 3°C or +30°F to + 37°F, the frost alarm will be
activated, the symbol “ “ will flash.
1.
2.
1.
2.
3.
1.
2.
3.
