manualshive.com logo in svg

Life Gear 26580, Owner'S Manual, Page: 9 / 21

Share
Download
Life Gear 26580 Owner'S Manual Download Page 9

 

8

 

2. Front and Rear Stabilizers Installation 

Position the Front Stabilizer (2) in front of the Front Main Frame (21) and align bolt holes. 
Attach the Front Stabilizer (2) onto the front curve of the Front Main Frame (21) with two 
M8x70 Bolts (6), two Ø8xØ25x2 Big Curve Washers (77), and two M8 Cap Nuts (3).   
Tighten bolts with the Multi Hex Tool with Phillips Screwdriver provided. 
Position the Rear Stabilizer (64) behind the Rear Main Frame (46) and align bolt holes. 
Attach the Rear Stabilizer (64) onto the rear curve of the Rear Main Frame (46) with two 
M8x70 Bolts (6), two Ø8xØ25x2 Big Curve Washers (77), and two M8 Cap Nuts (3).   
Tighten bolts with the Multi Hex Tool with Phillips Screwdriver provided. 
 

Hardware: 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2

6

3

77

3

77

67

3 77

64

6

3

77

21

46

Multi Hex Tool with Phillips Screwdriver

  S8, S13, S14, S15 

Tool: 

(3) Cap Nut M8 

4 PCS 

(6) Bolt M8x70

4 PCS 

(77) Big Curve Washer 

Ø8xØ25x2 

4 PCS 

Summary of Contents for 26580






















Reviews:

No comments