background image

Clean:

• Upholstery with mild soap and water.
• Guide rods with a cotton cloth.
• Hand grips with mild soap and water.
• Frame damage can be repaired with touch-up paint can be purchased from your LifeFitness customer service representative at

(800)328-9714.

Inspect:

•  Cables for wear or damage and proper tension (should not exceed 3/4” deflection.)  Pay close attention at bends and attachment

points.

•  Hardware should be checked for looseness. Tighten as required.
•  Frames should be inspected for wear or damage.
•  Hand Grips should be checked for wear or damage

Lubricate:

• Lube the Guide Rods. Apply the lubricant to a cotton cloth, then run the cotton cloth up and down the guide rods as needed. Do not

spray lubricant directly on the Guide Rods.

PREVENTATIVE MAINTENANCE TIPS

There is a risk assumed by individuals who use this type of equipment. To minimize risk, please
follow these rules:

2. Do not allow minors or children to play on or around this equipment.

1. Inspect equipment daily. Tighten all loose connections and replace worn parts immediately.
    Failure to do so may result in serious injury.

3. Exercise with care to avoid injury.

4. Consult your physician before beginning any exercise program.

12

Thank you for purchasing the LifeFitness CLUB SERIES LAT PULLDOWN. If unsure of proper use of

equipment, call your local LifeFitness  distributor or call the LifeFitness customer service department at

(800) 328-9714.

CAUTION-PLEASE READ

Action

DAILY WEEKLY QUARTERLY BI-ANNUALLY AS NEEDED

CLEAN

Upholstery

X

Guide Rods

X

Hand Grips

X

INSPECT

Visual Overall

X

Cables

X

Hardware

X

Frame

X

Hand Grips

X

LUBRICATE

Guide Rods

X

WARRANTY INFORMATION

10 YEARS

STRUCTURUAL FRAME

 3 YEARS

PILLOW BLOCKS, PULLEYS, WEIGHT PLATES AND GUIDE RODS

 1 YEAR

CABLES

90 DAYS

UPHOLSTERY

Summary of Contents for CSLAT















Reviews: