background image

IMPORTANT

!

CHECK THE BELT EDGE UNDER THE TREADMILL TO VERIFY THE BELT DOES NOT INTERFERE WITH LIFE-
SPRING BRACKETS AND THE BELT IS PROPERLY SET WITHIN THE BELT GUIDES.

Physical Dimensions:

Length

80 inches / 203 centimeters

Width

37 inches / 94 centimeters

Height

62.25 inches / 158 centimeters

Weight

95Ti:

450 pounds / 204 kilograms

95Te:

455 pounds / 206 kilograms

Step-up Height:

9.5 inches / 24 centimeters

PRE-OPERATION CHECKLIST 

(A digital version of the Operation Manual can be found on the attached CD.)

Ensure that all fasteners are tight.

Make sure the STRIDING BELT is properly tensioned and aligned according to the Operation Manual.

Check the operation of the STOP switch and tether switch assembly.

(See Operation Manual.)

Confirm the display console is set to English or Metric units.

(See Optional Settings ENG/MET in Operation Manual.)

Refer to the Operation Manual for real time clock setting.

Read the entire Operation Manual before using the treadmill.

LISTE DES VÉRIFICATIONS À EFFECTUER AVANT LA MISE EN MARCHE

(Une version électronique du Manuel de l'utilisateur peut être trouvée sur le CD)

Vérifiez si tous les dispositifs de fixation sont serrés.

Assurez-vous que le TAPIS est bien tendu et aligné, conformément aux instructions du manuel d'utilisation.

Vérifiez le fonctionnement de l'interrupteur d'ARRÊT et reliez-le 

(cf. Manuel de l'utilisateur).

Vérifiez si la console d'affichage est sur le système métrique ou anglais.

(Référez-vous aux réglages facultatifs relatifs aux systèmes de mesure dans le Manuel de l'utilisateur.)

Consultez le Manuel de l'utilisateur pour le réglage de l'horloge en temps réel.

Lisez le Manuel de l'utilisateur dans son intégralité avant d'utiliser le tapis roulant.

Before attempting to operate your Treadmill, it is imperative that you familiarize yourself with the contents of the
Operation Manual. If your Life Fitness treadmill does not respond as described in the OPERATION MANUAL contact the
nearest Life Fitness Service Center as listed in the OPERATION MANUAL.

Life Fitness Customer Support Services

(800) 351-3737 or (847) 451-0036

Prior to your call, please be sure you have located and noted the

MODEL NUMBER & SERIAL NUMBER.

The Model and Serial number are located behind the left end cap of the unit.

©2008 Life Fitness, a division of Brunswick Corporation. All rights reserved.
Life Fitness is a trademarks of Brunswick Corporation.

Polar is a registered trademark of Polar Electro, Inc.

M051-00K65-C002

03.08

Summary of Contents for 95T









Reviews: