background image

 

Lifa Air Oy Ltd. 

• Vellamonkatu 30 B, 00550 Helsinki, Finland • Tel: +358 9 394 858 

 

 

Safety 

  

The  following  safety  precautions  must  be  taken  into  account  in  order  to  avoid  injury  to 
personnel or damage to the environment or to the Lifa Duct Control Cleaning Robot itself.   
  
Following these instructions will ensure the safe and uninterrupted use of the machine.  

  

  The  Lifa  Duct  Control  Cleaning  Robot  is  both  electrically  and  pneumatically  operated  unit. 

The electrical power for the Duct Control Cleaning robot’s drive-motor come from the battery 
of the  Duct  Control  Manual  or  Mini.  The  battery of  Duct  Control  Manual  or  Mini  should  be 
charged every day after using and stored with fully charged battery only. 

 

  The 12 V battery of Duct Control Manual or Mini should be charged by the original charger 

connected to a single phase 110/230 V, 50/60 Hz.  
 

  The constant air flow for running the brush motor must have 340 l/minute in 7 bar pressure. 

Use only approved hoses for compressed air. 

 

  The equipment must not be positioned or used in places where there is a risk of explosion or 

hazardous substances.  

 

 

The equipment must not get wet and it has to be protected from moisture, vibration 
and wind.   

 

  Foreign objects must not be inserted or fitted into the equipment.  

 

  The machine cannot be covered during the use  

 

  The  user  must  ensure  that  the  appliance  is  adjusted  for  the  task  and  that  the  statutory 

requirements are met.   

 

  Be careful with sharp edges in the ductwork.  

 

  Use only accepted ladders or stands when working with Duct Control Cleaning Robot.  

 

  Wear  protective  mask,  eye  protection  glasses,  overall,  gloves  shoes  etc.  according  to  the 

requirements of the working place/environment.    

 

  In any questions, contact Lifa Air Ltd, or an authorized dealer. 

 
 

Summary of Contents for LIFA Duct Control Cleaning Robot


















Reviews: