background image

Operational Modes

16

5.0

O

PERATIONAL

 M

ODES

5.1

Normal Mode

When the UPS is in Normal Mode, the Normal Mode Indicator illuminates green.

5.2

Buck/Boost Mode

The Automatic Voltage Regulator (AVR) circuitry compensates for fluctuations in mains power, such 
as voltage surges and sags. The Liebert PSI XR compensates for these by raising the undervoltage 
(boost) or lowering the overvoltage (buck). The AVR operates automatically and maintains the output 
voltage to the connected equipment without utilizing the batteries.

5.3

Battery Mode

The UPS switches to Battery Mode in the event of an extreme input voltage/frequency condition or 
mains failure.

When the UPS is in Battery Mode, the Battery Indicator illuminates amber and an alarm sounds at 
2-second intervals. As capacity decreases, fewer indicators remain illuminated.

When a Low Battery condition occurs, the Battery Indicator flashes amber and an alarm sounds at 
one-second intervals. For approximate battery run times, refer to 

Table 8

.

5.4

Battery Recharge Operation

Once mains power is restored, the UPS resumes normal operation, and the Battery Charger begins 
recharging the batteries.

“«ˆVœ˜°Vœ°ÕŽÊ

ÊÊÊÊÊ/Ê>˜`ʘÃÌÀՓi˜Ì>̈œ˜ÊvœÀʈ˜`ÕÃÌÀÞ

->iÃ\

Ê

³{{Ê­ä®Ê£ÓÇÎÊxÇäÊÓÓäÊÊÊ

7iLÈÌi\

ÊÜÜÜ°>“«ˆVœ˜°Vœ°ÕŽÊÊÊ

“>ˆ\

ÊÃ>iÃJ>“«ˆVœ˜°Vœ°ÕŽÊÊ

Liebert UPS user manual

Summary of Contents for PS1000RT3-230XR































Reviews: