background image

           

MT86H

 

Operation

 

and

 

Maintenance

 

Manual

 

5

 

 

 

Fig. 1-7 

 

Fig. 1-8 

 

Fig. 1-9 

!

When driving the truck under full 

load on a slope: 

 Do not brake the truck abruptly when 

driving downhill; 

 Never disengage the clutch or coast 

the truck at neutral gear when driving 

downhill; 

 Do not make a sharp turn. 

6) When the truck starts running, the cargo body 

is tiltable; thus irrelevant personnel wandering 

around the truck is dangerous and shall be 

prohibited. 

1.3 Other precautions 

1) Unauthorized modification is not allowed. Any 

modification without permission from the 

Company may lead to an accident, and users 

shall contact with the Marketing Dept. of the 

Company in advance. The Company assumes no 

liability for the casualties and damages incurred 

therefrom. 

2) When lifting the cargo body to repair the 

components beneath, the stay bar of the cargo 

body should be set to a safe position for support, 

and restored once the repair is finished. 

3) Always inspect the tyre from the side and never 

stay before or behind the rotating tyre. 

Summary of Contents for MT86H






































































































































































Reviews: